Omron ZW-7000 Series Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 336

Omron ZW-7000 Series Скачать руководство пользователя страница 119

Performing internal logging

ZW-8000/7000/5000
User's Manual

117

3

Opera

tio

n durin

g RUN Mo

de

Performing Internal Logging with Parallel I/O

The logging start and end timings can be specified using LOGGING input signals from parallel I/O. When doing

so, follow the procedure below to set the data logging conditions.



Multi view Explore

: [System] (double-click)

→

Edit pane

: [Sensor Settings] icon (

)

→

Sensor settings window

: [Internal logging setting]

1

Set the logging conditions for internal logging.

There are three settings: Number of logging, number of logging decimation, and overwrite mode.

LOGERR signal is turned ON at the following cases:

• Overwrite mode is OFF

• 2,000,000 items have already been logged in the internal memory at the beginning of logging.

To continue to log regardless of the logging count while LOGGING input signal is turned ON, set as

below:

• Number of logging data: 0

• Overwrite mode: ON

When the number of loggings reaches 2,000,000, past logging data is overwritten and logging continues

on the latest data.

Overwrite mode and label insert mode cannot be used at the same time.

2

Set the output conditions of internal logging data.

Set the conditions for the external output using the non-procedural command LO.

Item

Setting item

Setting value

Description

Internal logging
setting

Number of
logging data

0 to 2000000
(default value: 100000)

Set the number of data to save for each internal logging
output data.

Internal logging
settings

0 to 1000
(default value: 1)

Set the interval of saving internal logging data.
If 1 is set, all data is saved. If 2 is set, one measured data is
saved every two measurements.
If 0 is set, data is saved only when the hold value is applied.

Overwrite mode

OFF (default value)/ON

Set whether to make the internal logging mode run in
overwrite mode.
Sets the operation to be performed when the logging count
exceeds the set number of logging data.
OFF: Internal logging is stopped.
ON: The oldest logging data is overwritten.

Label insert
mode

OFF (default value)/ON

Set the operation to be performed when logging input is
turned on.
OFF: No operation.
ON: When logging input is turned on, inserts label into log-
ging data.

Item

Setting item

Setting value

Description

Internal logging
setting

Output data
format

ASCII (default value)/
Binary

Select the output format for outputting internal logging data.

«
...
117
118
119
120
121
...
»

Содержание ZW-7000 Series

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды