Omron ZW-7000 Series Скачать руководство пользователя страница 116

Страница: 116 / 336

Performing internal logging

114

ZW-8000/7000/5000

User's Manual

3-8 Performing internal logging

Up to 2000000 data of measurement values can be logged in the Sensor Controller's internal memory.

Internal logging can be started or ended using Sysmac Studio, parallel I/O, or non-procedural communications

commands.

The operating procedures for each method are shown below.

The settings that can be enabled for each method are shown below.

Internal logging cannot be executed when in the following settings.

• When overwrite mode is ON or when the measurement cycle (internal synchronous measurement mode) is less

than 40µs

Internal logging by Sysmac Studio

Data logging conditions and logging start/end timing can be set with Sysmac Studio.



Multi view Explore

: [(ZW model name)] (double click)

→

Edit pane

: [Online] icon (

)

→

Online setting window : [Internal Logging]

Function

Sysmac Studio

Parallel I/O

Non-procedural commu-
nications commands

Specify start timing

Press the "Logging Start" button.

LOGGING input ON

Send LS command

Specify end timing

Stops automatically after the specified
number of logging data has been saved.

LOGGING input OFF

Send LE command

Terminate logging

After pressing the "Logging Start" button,
press the displayed "Terminate" button

LOGGING input OFF

LE command

Output logging data

Press the "Save to file (Sensor

→

PC)"

button.

Send LO/LG
command

Send LO/LG command

Clear logging data

• Automatically cleared after the "Logging

Start" button is pressed if clear logging
data is turned ON when logging starts

• Cleared when "Clear Logging Data" button

is pressed

Send LC command

Get logging information

Press the "Get logging information" button.

Send LI command

Function

Sysmac Studio

Parallel I/O

Non-procedural
communications
commands

Overwrite mode

Sets the operation to be performed when the logging
count exceeds the set number of logging data.

OFF: Internal logging is stopped.
ON : The oldest logging data is overwritten.

OFF

ON/OFF

Label insert mode

Sets the operation to be performed when logging input
is turned on.

OFF: No operation.
ON : When logging input is turned on, inserts label

into logging data.

OFF

ON/OFF

Output data format

−

ASCII

ASCII/Binary

Important

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды