background image

 

Safety Manual   TECHMAN ROBOT Safety System 3.3                                                    10 

1. Comprehensive Information 

 Overview 

This chapter describes the comprehensive important safety information of TM Robot. The user and system 
integrator of TM Robot must read and fully understand this chapter before using this robot. 

 

 Applicable Product Version 

This document is only applicable to the combination of the following software and hardware versions of TM Robot. 
Users can check the hardware version and software version on “Techman Robot Product Brief Information” sheet 
in the control box carton, or through these methods: checking the hardware version on the product label on the 
control box and checking the software version from the software information button in the UI of TMflow. If the 
software version of the robot has been upgraded and is different from the original out-of-the-box one, users should 
only check the software version from the UI of TMflow. 

 

Safety System version: 

TECHMAN ROBOT Safety System 3.3* 

Hardware version 

HW 3.2 

Software version 

SW 1.80 

*Within the scope of hardware and software combination above, the safety system 

version remains the same as TECHMAN ROBOT Safety System 3.3 

Table 1: Safety System Version 

 

Users shall confirm whether the software and hardware version of the TM Robot is consistent with the applicable 
product version of this 

Safety Manual

. The Corporation is not responsible for any safety issues caused by referring 

to the safety instruction of an incorrect version. 
 

 Safety Warning Symbols 

The following table defines the levels of the safety warning symbols that are marked in each paragraph in this 
Manual. Read carefully and comply with each paragraph to avoid harm to people or equipment. 
 

 

DANGER: 

Identifies an imminently hazardous situation which, if not avoided, is likely to result in serious 
injury, and might result in death or severe property damage. 

 

WARNING: 

Identifies a potentially hazardous situation which, if not avoided, will result in minor or moderate 
injury, and might result in serious injury, death, or significant property damage. 

 

CAUTION: 

Identifies a potentially hazardous situation which, if not avoided, might result in minor injury, 
moderate injury, or property damage.   

Содержание Techman Robot























































Отзывы: