Omron SYSMAC NY Series Скачать руководство пользователя страница 195

Страница: 195 / 260

7-2-7

Replace the CFast Card

Use the following procedure to replace the CFast Card.

Prepare the new CFast Card.

Additional Information

• Refer to

1-4 Product Configuration Box PC

on page 1-5 for the installed CFast Card model.

• Refer to

3-10-4 CFast Cards

on page 3-24 for the available CFast Card models.

• Refer to

CFast Card Specifications

on page 4-13 for specification details.

To replace the CFast Card:

Power OFF the Box PC.

Remove the CFast Card slot cover.

UST

orporatio

Kyoto, 600-8530 J

P AN

MADE IN

E NETHERLANDS

PROD

UCT

1) Remove the two screws

2) Remove the cover

Pull the plastic Pull Tab

to remove the CFast Card

from the Box PC.

7 Maintenance

7-21

NY-series Industrial Box PC Hardware User's Manual (W553)

7-2
Corrective Maintenance

7-2-7

Replace the CFast Card

Содержание SYSMAC NY Series





































































































































































































































































Результаты поиска

Содержание SYSMAC NY Series

Отзывы:

Бренды по названию

Популярные бренды

Omron SYSMAC NY Series, Руководство пользователя по оборудованию

Результаты поиска

Содержание SYSMAC NY Series

Отзывы:

Бренды по названию

Популярные бренды