Omron SYSMAC NY Series Скачать руководство пользователя страница 180 | Manualshive

Страница: 180 / 260

Omron SYSMAC NY Series Скачать руководство пользователя страница 180

7-2-2

Remove the Cover

Applicable for products with a cooling layer that has a removable Cover.

The Cover of the cooling layer provides access to the following items.
• Battery
• Fan Unit (applies to products with active cooling)
The inside of the Cover contains a label with the battery replacement date.
No tools are required to open the Cover.
Use the following procedure to remove the Cover of the Box PC.

1

Power OFF your Box PC if it has active cooling.

Precautions for Safe Use

Do not remove the fan cover while the power is ON. Contact with the rotating fan may result in
injury.

2

Remove the Cover.

1

3

2

1) Pull the lever

1

to unlock the Cover.

2) Lift the side

2

to tilt the Cover.

3) Remove

3

the complete Cover.

The Cover is removed.
To mount the Cover, position the side of the Cover in the Box PC and push the cover in place.
The lever will lock in place.

7 Maintenance

7-6

NY-series Industrial Box PC Hardware User's Manual (W553)

«
...
178
179
180
181
182
...
»

Содержание SYSMAC NY Series





































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды