Omron SYSMAC NY Series Скачать руководство пользователя

Страница: 119 / 260

5-2

Install Options

This section describes the installable options for the Industrial Box PC.

5-2-1

Install a Drive

A drive is a storage device for the Industrial Box PC.

Additional Information

• Depending on the product configuration 0, 1 or 2 drives can be pre-installed.

Refer to

1-4 Product Configuration Box PC

on page 1-5 for details.

• Depending on the CPU type one or two drives are supported.

Refer to

4-1-5 CPU Specifications

on page 4-6 for the number of supported drives.

• Refer to

3-10-5 HDD and SSD Storage Devices

on page 3-25 for the recommended drive

models.

• Refer to

4-1-7 Storage Device Specifications

on page 4-11 for drive specifications.

Prepare the following items:
• The drive

A drive is not supplied with the Box PC.

• The drive bracket with mounting screws

These are supplied with the Box PC.

To install a drive:

Ensure the Box PC is OFF.

Remove the drive cover.

1) Push the lock lever

2) Tilt the drive cover

3) Remove the drive cover

5 Installation

5-5

NY-series Industrial Box PC Hardware User's Manual (W553)

5-2 Install Options

5-2-1

Install a Drive

Содержание SYSMAC NY Series





































































































































































































































































Результаты поиска

Содержание SYSMAC NY Series

Отзывы:

Похожие инструкции для SYSMAC NY Series

Бренды по названию

Популярные бренды

Omron SYSMAC NY Series, Руководство пользователя по оборудованию

Результаты поиска

Содержание SYSMAC NY Series

Отзывы:

Похожие инструкции для SYSMAC NY Series

Бренды по названию

Популярные бренды