718
V600/V620 ID Controller Protocol
Appendix P
Receive Data Word Allocation (4th Operand of PMCR(260))
None.
Note
1.
Write data designated for hexadecimal is sent beginning with the largest offset from the send data
words.
2.
Always set an even number of digits for the write data.
Auto-write (ASCII/1) (Sequence No. 526 (Hex 020E))
This sequence is used when the number of Heads to be written to the Carrier is 1.
Send Data Word Allocation (3rd Operand of PMCR(260))
The send data word allocation is similar to that of Sequence No. 518 (Write (ASCII/1)).
Receive Data Word Allocation (4th Operand of PMCR(260))
The receive data word allocation is similar to that of Sequence No. 518 (Write (ASCII/1)).
Note
For auto-write (AW), a response is not returned if the number of Heads is not written by the Carrier, the
Abort Bit must be turned OFF to terminate the sequence.
Auto-write (Hex/1) (Sequence No. 527 (Hex 020F))
This sequence is used when the number of Heads to be written to the Carrier is 1.
Send Data Word Allocation (3rd Operand of PMCR(260))
The send data word allocation is similar to that of Sequence No. 522 (Write (Hex/1)).
Receive Data Word Allocation (4th Operand of PMCR(260))
The receive data word allocation is similar to that of Sequence No. 522 (Write (Hex/1)).
Note
For auto-write (AW), a response is not returned if the number of Heads is not written by the Carrier, the
Abort Bit must be turned OFF to terminate the sequence.
Polling Auto-write (ASCII/2) (Sequence No. 528 (Hex 0210))
This sequence is used when the number of Heads to be written to the Carrier is 2.
Send Data Word Allocation (3rd Operand of PMCR(260))
The send data word allocation is similar to that of Sequence No. 519 (Write (ASCII/2)).
Receive Data Word Allocation (4th Operand of PMCR(260))
The receive data word allocation is similar to that of Sequence No. 519 (Write (ASCII/2)).
Note
1.
Execute Sequence No. 545 (Polling Auto-write Command Processing Cancel) to cancel the polling
auto-write.
2.
Retry processing is not performed for this sequence.
Polling Auto-write Subcommand (ASCII/2) (Sequence No. 529
(Hex 0211))
This sequence is used when the number of Heads to be written to the Carrier is 2. Up to 118 digits of data can
be written for each Read/Write Head.
Send Data Word Allocation (3rd Operand of PMCR(260))
The send data word allocation is similar to that of Sequence No. 519 (Write (ASCII/2)). However, the leading
address No., number of write, and write data are not used and become undefined.
Receive Data Word Allocation (4th Operand of PMCR(260))
None.
Содержание SYSMAC CJ1W-SCU21-V1
