Omron SCARA YRCX Series Скачать руководство пользователя страница 422 | Manualshive

Страница: 422 / 506

Omron SCARA YRCX Series Скачать руководство пользователя страница 422

7

8

9

10

11

12

13

11-12 Chapter 11 User program examples

2.3

Pick and place of stacked parts

■

Overview

The following is an example for picking up parts stacked in a maximum of 6 layers and 3 blocks
and placing them on the conveyor.
The number of parts per block may differ from others.
Parts are detected with a sensor installed on the robot hand.

Pick and place of stacked parts

Conveyor

P5

P1

Block 1

P2

Block 2

P3

Block 3

Z=0.0

33C11-R7-00

■

Precondition

1. I/O signal

DI (30)

Component detection sensor

1: Parts are supplied

DI (31)

Robot hand open/close

0: Open / 1: Close

• Robot hand open/close time is 0.1 seconds.

2. The points below should be input beforehand as point data.

P1

Bottom of block 1

P2

Bottom of block 2

P3

Bottom of block 3

P5

Position on conveyor

3. Movement proceeds at maximum speeds but slows down when in proximity to the part.

Processing flow

P5

P1

P5

P1

P4=WHERE

P4=WHERE

High speed

High speed

Slow

Set the current position

into point data (P4)

P4=WHERE

Set the speed at maximum

Load the part onto

conveyor position (P5)

Move to position (P4)

during parts detection

Move to P1

Slow down

33C12-R7-00

4. Use a STOPON condition in the MOVE statement for sensor detection during movement.

«
...
420
421
422
423
424
...
»

Содержание SCARA YRCX Series



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов