Omron NYB17-11 Скачать руководство пользователя страница 77

Страница: 77 / 244

Refer to

2-9-9 UPS

on page 2 - 21 for details.

Ensure the UPS is connected to the Box PC with a USB cable.
Refer to

5-8-1 Connect UPS Using the USB Connector

on page 5 - 52 for details.

Open the Power Attendant Lite Utility installer folder and activate the installer file

setup.exe

Follow the installer steps to complete the installation.

The Power Attendant Lite Utility is installed.

Configuration

Configure the Power Attendant Lite Utility before using the Box PC with a UPS connected using USB.

To configure the Power Attendant Lite Utility:

Activate the icon of the Power Attendant Lite Utility to start the software.

A UPS selection window will be displayed.

Select the connected UPS.
A Login window will be displayed.

Admin

and password

omron

The Top window with UPS status information will be displayed.

Configure the parameters for your specific situation.

3 Software

3 - 17

NY-series Industrial Box PC User's Manual (W553)

3-2
Support Software

3-2-6 Power Attendant Lite Utility

Содержание NYB17-11





















































































































































































































































Результаты поиска

Содержание NYB17-11

Отзывы:

Похожие инструкции для NYB17-11

Бренды по названию

Популярные бренды

Omron NYB17-11, Руководство пользователя

Результаты поиска

Содержание NYB17-11

Отзывы:

Похожие инструкции для NYB17-11

Бренды по названию

Популярные бренды