Omron NX1P2 series Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 264

background image

5-3-7

Attaching Markers

Markers can be attached to NX Units and their terminal blocks to identify them.
The plastic markers made by OMRON are installed for the factory setting. The ID information can be
written on them.
Commercially available markers can also be installed.
Replace the markers made by OMRON if you use commercially available markers now.

Markers

The marker attachment locations on the NX Units depend on the type of external connection termi-
nals. Refer to the user’s manual for the NX Units that you will use for the marker attachment locations.

l

Installation Method

Insert the protrusions on the markers into the marker attachment locations on the NX Units and ter-
minal blocks on NX Units.

Marker

Marker

Marker attachment location

Marker attachment location

<Terminal block>

<Unit>

l

Commercially Available Markers

Commercially available markers are made of plastic and can be printed on with a special printer.
To use commercially available markers, purchase the following products.

Product name

Model number

Manufactured by Phoenix Contact

Manufactured by Weidmuller

Markers

UC1-TMF8

DEK 5/8

Special marker printer

UM EN BLUEMARK X1

PrintJet PRO

The markers made by OMRON cannot be printed on with commercially available special printers.

5 Installation and Wiring

5-27

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

5-3
Mounting and Removing Units

5

5-3-7

Attaching Markers

«
...
169
170
171
172
173
...
»

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX1P2 series

Бренд: CAME Страницы: 4

Бренд: Alcad Страницы: 6

Бренд: Omron Страницы: 13

Бренд: Atmel Страницы: 2

Бренд: JAKA Страницы: 37

H8S/2646 Series

Бренд: Renesas Страницы: 20

Бренд: ATTO Technology Страницы: 2

Бренд: PairGain Страницы: 48

Бренд: Xtreme Страницы: 83

Бренд: IEI Technology Страницы: 213

Threat Analysis Reporter TAR HL/SL/MSA

Бренд: 8e6 Technologies Страницы: 22

Бренд: NetApp Страницы: 28

Бренд: Acromag Страницы: 20

Бренд: 4ms Company Страницы: 4

Бренд: Hitachi Страницы: 378

Schottky Barrier Diodes MA3XD21

Бренд: Panasonic Страницы: 3

Schottky Barrier Diodes MA2SE01

Бренд: Panasonic Страницы: 3

Schottky Barrier Diodes MA2SD32

Бренд: Panasonic Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды