Omron NX1P2 series Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 264

background image

Momentary Power Interruption with Continued Operation

Execution of the user program will continue if a momentary power interruption is less than the follow-
ing times.

The CPU Unit will not interrupt
execution of user program

Momentary power interruption time

from voltage drop until recovery

Voltage drop

Executing user program

DC: 20.4 V max.

Power OFF detection time

2 to 8 ms

Voltage recovery

Processing after Power Interruption Is Confirmed

After a power interruption is confirmed, the CPU Unit performs the following processing and then
stops.

Item

Description

I/O refresh

I/O refresh stops, and all outputs are turned OFF. Tag data links
via the EtherNet/IP stop.

Processing

SD Memory Card access in
progress

Any writing is interrupted, files are closed, and the Card is un-
mounted.

Transferring user program
(including online editing)

Interrupted.
As a result, an error will occur the next time that the power is
turned ON. The Controller will not operate.

User program execution

User program execution is aborted even during execution of an in-
struction.

Saving event log

The time that a power interruption occurs and the cause (primary
power interruption) of the interruption are recorded.

5-1-3

Resetting the Controller from the Sysmac Studio

You can reset the CPU Unit from the Sysmac Studio.
A reset from the Sysmac Studio follows the same operation as cycling the power supply of the Unit
power.
Resetting is possible, however, only when the CPU Unit is in PROGRAM mode.
Confirm the following status before the CPU Unit Reset.
• Check the status of output loads.
• Make sure that SD Memory Card access is not in progress.

5 Installation and Wiring

5-7

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

5-1 Processing at Power ON and Power OFF

5

5-1-3

Resetting the Controller from the Sysmac Studio

«
...
149
150
151
152
153
...
»

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX1P2 series

Бренд: 3Com Страницы: 8

Бренд: Salus Страницы: 16

ST62GP-EMU2 HDS2 Series

Бренд: STMicroelectronics Страницы: 58

Бренд: Renesas Страницы: 2

Бренд: Infoblox Страницы: 13

Бренд: Aewin Technologies Страницы: 86

500 - DATASHEET REV 003

Бренд: Intel Страницы: 67

Бренд: CAME Страницы: 32

AirBridge VS-YOFIMN-000

Бренд: Vivint Страницы: 2

STEVAL-SCR002V1

Бренд: ST Страницы: 28

Бренд: Advantech Страницы: 70

Бренд: YASKAWA Страницы: 87

Бренд: PairGain Страницы: 76

WSIL-1204-GT2-SFP2

Бренд: WAVESYS Страницы: 21

Database Appliance X6-2-HA

Бренд: Oracle Страницы: 473

Бренд: Velleman Страницы: 14

MEG CORELIQUID S280

Бренд: MSI Страницы: 21

Direct Dummy IC M3T-DCT42B-450

Бренд: Renesas Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды