manualshive.com logo in svg

Omron NX-IA3117, Руководство пользователя

Поделиться
Скачать
Omron NX-IA3117 Скачать руководство пользователя страница 145

5 - 29

5   I/O Refreshing

NX-series Digital I/O Unit User’s Manual (W521)

5-

2  I/O Refres

hing

 Meth

od
s

5

5-

2-10  An Example of T

urning ON Output

s at S

p

ecific T

imes Af

ter
 the Sensor Inpu

ts

 C

hange

The following shows an example that uses an Input Unit NX-ID3344 that supports input refreshing with 
input changed time and an Output Unit NX-OD2154 that supports output refreshing with specified time 
stamp to turn ON the output to the external output device at a specific time after the input changed time 
from the sensor.

• In this example, 500 ms after the sensor input that is connected to input bit 00 of an Input Unit 

NX-ID3344 changes to ON, output bit 00 of an Output Unit NX-OD2154 changes to ON.

• The following determinations are performed to normally operate the programming.

a) When the specified time is set to an Output Unit NX-OD2154, the validity of the specified time is 

determined to make sure that the specified time is not a previous DC time.

b) With an Output Unit NX-OD2154, the output was normally refreshed at the specified time is 

determined.

5-2-10 An Example of Turning ON Outputs at Specific Times After the 

Sensor Inputs Change

Specifications of Sample Programming

EtherCAT
Coupler Unit

Output Unit
NX-OD2154

Input Unit
NX-ID3344

Built-in EtherCAT port

NJ-series CPU Unit

External output device
(Output)

Workpiece

Sensor
(Input)

NX-ID3344
Input Bit 00

NX-OD2154
Output Bit 00

500 ms

Содержание NX-IA3117























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды