Omron NX-CSG Series Скачать руководство пользователя

Страница: 5 / 17

Rev. 1.0

2. EtherNet/IP Safety Connection Procedure

This section describes the procedures for connecting the Omron safety I/O block and the safety

controller via EtherNet/IP safety.

2.1. Safety Controller Setup

Set up the Safety Controller.

The Sysmac Studio is used for the Safety Controller setup, please install before proceeding.

2.1.1. Hardware configuration and IP address Settings

Configure the hardware of the Safety Controller and set the IP address using the hardware

switches.

Precautions for Correct Use

Before setting up turn the power supply is OFF.

If it is ON, the settings described in the following steps and subsequent procedures may not be

applicable.

Make sure Safety Controller is powered

OFF.

Connect Safety CPU Unit to
Communication Control Unit.

Setting the IP address:
1 is for port 1.
2 is for port 2A and 2B.

If the rotary switches are set to 00 then

the IP address for port 1 and 2 are set

using Sysmac Studio.

If the rotary switches are between 01
to FF (001 to 255 in decimal) then:
Port 1 default IP address =
192.168.1.xxx
Port 2A and 2B default IP address =
192.168.250.xxx

Set the rotary switch for port 1 and 2 to 00

Communication Control Unit

Safety

CPU

Unit

End

Cover

Rotary switches

Built-in EtherNet/IP
ports

PORT1
PORT2A
PORT2B

Содержание NX-CSG Series


















Результаты поиска

Содержание NX-CSG Series

Отзывы:

Похожие инструкции для NX-CSG Series

Бренды по названию

Популярные бренды

Omron NX-CSG Series, Как подключить

Результаты поиска

Содержание NX-CSG Series

Отзывы:

Похожие инструкции для NX-CSG Series

Бренды по названию

Популярные бренды