Omron NE1A-EDR01 Скачать руководство пользователя страница 60

Страница: 60 / 109

Mitsubishi Ethernet Interface Module Settings

Section 4-4

4-4

Mitsubishi Ethernet Interface Module Settings

This section describes how to make the settings for the Mitsubishi QJ71E71-
100 Ethernet Interface Module.

Note

Refer to the following manuals for more details on subjects such as proce-
dures for making settings.

• QSCPU User’s Manual (Function Explanation, Program Fundamentals)

• Q Corresponding Ether Interface Module User’s Manual (Basic)

4-4-1

PC Parameters

I/O Allocations

Set the type of Module mounted on the Base Unit, the I/O signal range, etc.

Make the following I/O allocation settings.

Program

Set the program file name and the execution type (execution condition). The
program can be written to the CPU Module according to these settings.
In this example, the settings are made as shown in the following table.

4-4-2

Network Parameters

Make the settings for using the Ethernet Module as a network module. Select

MELSECNET/Ethernet

in the Network Parameters Window, and then make

the settings as shown in the following table.

EtherNet Operations

Make the common Module settings for using the Ethernet Module.

The settings for Ethernet operations are shown in the following table.

Item

Contents

Setting

Type

Set the type of Module that is mounted.

Intelli

Model name

Set the model name of the Module that is
mounted.

QJ71E71-100

Points

Set the number of points for each slot.

32 (32 points)

Start XY

Set the starting I/O number for each slot.

0000

Item

Contents

Setting

Program name

Set the name of the program.

MAIN

Execute type

Execution type (execution condition)

Scan

Item

Contents

Setting

Network type

Select the mounted Module.

Ethernet

Starting I/O No.

Set the starting address for the Module.

0000

Network No.

Set the network number for the Module.

Group No.

Set the group number for the Module.

Station No.

Select the station number for the Module.

Mode

Select the operating mode for the Module. Online

Item

Contents

Setting

Communication data
code setting

Select the communications data code.

Binary code com-
munication

Initial Timing

Make the OPEN setting.

Do not wait for
OPEN

IP
address
setting

Input format Select the input format for the IP address. Decimal

IP address

Set the local IP address.

192.168.250.18

Содержание NE1A-EDR01














































































































Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды

Omron NE1A-EDR01, Руководство по эксплуатации

Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды