Omron NE1A-EDR01 Скачать руководство пользователя страница 35

Страница: 35 / 109

Connecting to Ethernet (EtherNet/IP)

Section 2-4

2-4

Connecting to Ethernet (EtherNet/IP)

2-4-1

Setting the IP Address

This section describes methods for setting the IP address for the ED Router.

Method 1: The default IP address is 192.168.250.

IP_address_switch_set

value

The IP address is set with the rotary switches on the front of the
ED Router (IP ADR).

→

This method can be used to make a temporary or preliminary
connection to the Ethernet.
In this case, leave the TCP/IP Configuration setting at its
default value.

Method 2: Setting the TCP/IP Configuration from the Network Configura-

tor:

→

To set a particular local IP address, use the Network Configu-
rator.

The methods for setting the ED Router IP address are described below.

Method 1: Using the Default IP Address (192.168.250.

IP_address_switch_set value

)

The default IP address for the ED Router is
192.168.250.

IP_address_switch_set value

. The IP address switch is used to

set the IP address host ID.

IP address = 192.168.250.

IP_address_switch_set value

The host IC can be changed with the IP address switch. If 00 or FF is set, 01
will be used as the host ID.

The TCP/IP settings will be in the following default settings.

Method 2: Setting the TCP/IP Configuration from the Network Configurator

With this method, set the TCP/IP configuration, including the IP address, from
the Network Configurator.

Setting

Operating status

IP address

192.168.250.

IP_address_switch_set value

Subnet mask

255.255.255.0 (class C mask)

Default gateway

None (IP routing disabled)

Preferred DNS server

None

Alternate DNS server

None

Host name

None

Domain name

None

Baud rate

Auto-detect

Содержание NE1A-EDR01














































































































Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды

Omron NE1A-EDR01, Руководство по эксплуатации

Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды