manualshive.com logo in svg

Omron K6PM-TH, Руководство пользователя

Поделиться
Скачать
Omron K6PM-TH Скачать руководство пользователя страница 46

2   Installation and Wiring

2 - 10

K6PM-TH Thermal Condition Monitoring Device User’s Manual (H231)

2-3

Wiring

This section describes the wiring of the Main Units.

This section describes how to connect the Main Units to the Push-In Plus terminal blocks.

All terminals of the Main Unit are Push-In Plus terminals.

Precautions for Safe Use

• To prevent wire materials from smoking or igniting, use the wiring materials given in the fol-

lowing table.

• Make sure the crimp terminals for wiring are of the specified size.
• Do not insert more than one wire into each terminal insertion hole.
• Do not connect anything to terminals that are not being used.
• Do not wire anything to the release holes.
• Do not tilt or twist a flat-blade screwdriver while it is inserted into a release hole on the ter-

minal block. The terminal block may be damaged.

• Insert a flat-blade screwdriver into the release holes at an angle. The terminal block may 

be damaged if you insert the screwdriver straight in.

• Do not allow the flat-blade screwdriver to fall out while it is inserted into a release hole.
• Do not place product wiring in parallel with or in the same path as high-voltage or high-cur-

rent lines. Keep wiring separate from high voltages and power lines that draw large cur-
rents.

• Do not bend a wire past its natural bending radius or pull on it with excessive force. Doing 

so may cause the wire disconnection.

• When wiring the terminals, allow some leeway in the wire length.

Precautions for Correct Use

• When you are finished with wiring, make sure that no stranded wire comes loose.
• If you wire crossovers and connect terminal blocks in parallel, a large current will flow. Make 

sure that the current does not exceed 10 A.

• The terminal block may be damaged if the recommended tool is not used. Use the recom-

mended flat-blade screwdriver to operate the release holes.

2-3-1

How to Connect to the Push-In Plus Terminal Blocks

Recommended Wire

Stripping length

(Without Ferrules)

0.25 to 1.5 mm

2

 (AWG24 to AWG16)

8 mm

Содержание K6PM-TH







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды