Omron GX-AD0471 Скачать руководство пользователя страница 92

Страница: 92 / 394

6 Basic Specifications of Slave Units

6 - 8

GX-series EtherCAT Slave Unit User’s Manual

•

The code printed above the node address setting switches differs according to the unit version
of the IO-Link Master Unit, as shown below.

The Connectors are used to connect the communications cables.

RJ45 connectors are used for the communications connectors as shown below.

The specifications are shown below.

•

Electrical characteristics: Conforms to the IEEE 802.3 standard.

•

Connector structure: RJ45 8-pin modular connector (conforms to ISO 8877)

•

Terminal arrangement

Unit version

Code

Version 1.0

NODE ADDRESS

Version 1.1 or later

6-3-3

Communications Connectors

Digital I/O Slave Units, Analog I/O Slave Units, and Encoder Input

Slave Units

Pin No.

Signal name

Abbreviation

Send data +

TD +

Send data

−

Receive data +

RD +

Not used

−

Not used

−

Receive data

−

Not used

−

Not used

−

Hood

Frame ground

CN1

CN2

Содержание GX-AD0471











































































































































































































































































































































































































Результаты поиска

Содержание GX-AD0471

Отзывы:

Omron GX-AD0471, Руководство пользователя, Страница: 92 / 394

Результаты поиска

Содержание GX-AD0471

Отзывы: