Omron GX-AD0471 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 394

Omron GX-AD0471 Скачать руководство пользователя страница 20

16

GX-series EtherCAT Slave Unit User’s Manual

Version Upgrade Information

This section explains the functions that have been added or changed due to the unit version upgrade of
the GX-series EtherCAT Slave Units.
For the compatible versions of Support Software for the EtherCAT Slave Units, refer to

The following changes have been made in the upgrade from unit version 1.0 to 1.1 of the GX-series
Digital I/O Slaves, Analog I/O Slaves, and Encoder Input Slaves.

The following changes have been made in the upgrade from unit version 1.0 to 1.1 of the GX-series
IO-Link Master Unit.

*1. n = 0 to 7 ("n" represents the port number.)

Details of Upgrade from Unit Version 1.0 to 1.1

Item

Unit version 1.0

Unit version 1.1

Emergency message setting when the Slave Unit’s
power supply is turned ON

Emergency message noti-
fication is enabled at
startup.

Emergency message noti-
fication is not enabled at
startup.

Sysmac device
functions

Sysmac error status

Not supported.

Supported.

Saving node address settings

Not supported.

Supported.

Displaying the serial number

Not supported.

Supported.

Conformance to ESI specifica-
tions (ETG.2000 S (R) V1.0.1)

Supported.

Supported.

SII data checking

Not supported.

Supported.

Data attribute for Input Time Constant (3000 hex) for
Digital I/O Slave Unit

Attribute: R

Attribute: D

Bit objects
• Digital I/O bit objects for Digital I/O Slave Units (3020

hex and 3220 hex)

• Soft switches (bits) and status (bits) objects for

Encoder Input Slave Units (4021 hex and 4031 hex)

Not supported.

Supported.

Item

Unit version 1.0

Unit version 1.1

The following data that can be allocated to the I/O data
• Digital Input Data
• Digital Output Data

Not allocated by default.

Allocated by default.

Digital input collection

Not supported.

Supported.

The following objects are added to the manufacturer
specific objects.
• Vendor Name of the Last Connected IO-Link Device

(80n2 hex *1)

• Product Name of the Last Connected IO-Link Device

(80n3 hex *1)

• Vendor Name (90n2 hex *1)
• Product Name (90n3 hex *1)

Not supported.

Supported.

«
...
18
19
20
21
22
...
»

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов