background image

12

F3SG-SR-K

Quick Installation Manual

7. Pre-Operation Checklists / Maintenance Checklists

After wiring, mounting and beam alignment are done, check the operation of the F3SG-SR-K.

Pre-Operation Checklists

After installation, the highest level administrator must use the following checklist to verify the operation, plac

-

ing a check mark in each of the boxes.

Checklists

- Installation Condition Check

The machine itself does not prevent the operation of safety functions such as stopping.

The hazardous part of a machine cannot be reached without passing through the detection zone of the

F3SG-SR-K.

The  system is configured so that  the  F3SG-SR-K  can always detect a worker who is  working  in the

hazardous zone.

The interlock reset switch is installed in a location that provides a clear view of the entire hazardous zone

and it cannot be activated from within the hazardous zone.

The pre-reset switch is installed in a location inside the hazardous zone and where it cannot be operated

from outside the hazardous zone.

Safety distance has been calculated. Calculated distance: S = ( )mm

Safety distance has been calculated with larger object resolution when the Floating Blanking or Reduced

Resolution function is used. Calculated distance: S = ( )mm

The actual distance is equal to or greater than the calculated distance. Actual distance = ( )mm

Reflective surfaces are not installed in prohibited zones.

Not installed in a retro-reflective configuration.

When the Muting function is used, a muting sensor must be installed so that MUTING state should not

occur when a human body enters a detection zone of the F3SG-SR-K by mistake.

When the Muting function is used, a muting sensor must be installed so that MUTING state should not

occur when a human body enters a hazardous zone of a machine.

When the Muting function is used, MUTING state can be checked from where a worker operates or adjust

the machine.

A muting sensor consists of two independent devices.

It is not used in flammable or explosive atmosphere.

- Wiring Check Before Power Is Turned ON

When the power supply unit is connected to multiple devices, the power supply unit must have tolerance

against total rated current of the devices.

The power supply unit is a 24 VDC unit that conforms to the EMC Directive, Low-voltage Directive, and

output holding time specifications.

The power supply lines are wired with a proper polarity according to the wiring specifications of the PNP

or NPN setting.

Emitter/receiver cables are properly connected to the respective emitters/receivers.

Double insulation is used between I/O lines and the hazard potential (commercial power supplies, etc.).

When using PNP output, the outputs are not short-circuited to +24 VDC line. When using NPN output,

the outputs are not short-circuited to 0 VDC line.

When using PNP output, loads are not connected to +24 VDC line. When using NPN output, loads are

not connected to 0 VDC line.

All lines are not connected to commercial power source.

Model of emitter and receiver must be the same.

When two or more F3SG-SR-K systems are used, they are prevented from mutual interference with each

other.

Neither bracket must be loose.

Auxiliary output must not be used as safety output.

When using PNP output, +24 VDC line of the power supply must not be grounded. When using NPN

Mounting

Wiring

Operation check

Содержание F3SG-SR-K Series


























Отзывы: