manualshive.com logo in svg

Omron F3SG-RA, Руководство пользователя

Поделиться
Скачать
Omron F3SG-RA Скачать руководство пользователя страница 157

133

F3SG-R

User’s Manual

Chapter

4

Cas

c

ade Conne

ct

ion

Wiring/Installation

E

4-2-2. Connection Procedure

1.

Remove the caps from the primary sensor. Loosen the screw (M3 cross-shaped) to remove the cap.

2.

Connect the the the primary sensor and the secondary sensor with the F39-JGR2W Cascading Cable
(sold separately).

3.

If the length of the Cascading Cable is insufficient, connect the F39-JG

B-

 Double-Ended Cable

(sold separately) between the Cascading Cable and the power cable of the secondary sensor, as
required. (Cable length between sensors: 10 m max.)

- When attaching a cable or cap, securely fasten the screws (M2.5, recommended torque: 0.35 N•m).

Failure to do so may cause the cable/cap to come loose, leading to deterioration of the protective functions.

- Attaching/detaching of the cap and the Cascading Cable may cause misalignment of rubber grommet in the connector

assembly. Press the grommet to the bottom of the connector and attach the connector to the sensor again.

1.

1.

1.

1.

2.

2.

2.

2.

3.

3.

3.

3.

End Cap

End Cap

Cascading Cable F39-JGR2W-D

Double-Ended Cable F39-JG

B-D

Cascading Cable F39-JGR2W-L

Double-Ended Cable F39-JG

B-L

Receiver power cable

Emitter power cable

Emitter power cable

Receiver power cable

<Secondary sensor>

<Primary sensor>

Содержание F3SG-RA













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды