Omron F3SG-PG Series, Руководство пользователя, Страница: 420 / 473

390
Chapter
6
Wiring Exa
m
p
le
s
(f
or F3
SG-SR/PG)
F3SG-SR/PG
User’s Manual
Input/Output Circuit and Applications
6-2-1-7. Manual Reset Mode with Reset Switch Connector
[Wiring Example (F3SG-SR and F3SG-PGA-A/-L*8)]
• When using the Reset Switch Connector (F39-GCNY3), the following functions are not available.
- External Device Monitoring (EDM)
• When a functional earth is necessary, wire an earth cable according to the example in
6-2-1-1. Auto Reset Mode with
Optical Synchronization and EDM Unused
. Also refer to 5-4-4. Functional Earth Connection for more information.
F3SG-SRA

F3SG-PGA-A/-L

F3SG-SRB

F3SG-PGA-C

*8
S2 S1
24 V DC
24 V DC
F39-GC N Y3
F39-JGR3K-D
XS5F-D421 8 0-F
F39-JG A-D
I N 1 I N 2
L1
W iring for N P N *1
OSSD 1 (Blac
k)
OSSD 2 (
W
hite)
24
V
/0
V
(Bro
w
n)
TEST (Blac
k)
N
ot
u
sed (
W
hite)
24
V
/0
V
(Bro
w
n)
0
V
/24
V
(Bl
u
e)
0
V
/24
V
(Bl
u
e)
A
UX (Red)
MUTE B (Pink) MUTE A (Gr
a
y)
RESET (Y
ello
w
)
0
V
/24
V
(Bl
u
e)
RESET (
W
hite)
24
V
/0
V
(Bro
w
n)
A
UX (Blac
k)
OPERA
TI
N
G
RA
N
GE SELECT
I
N
PUT (Y
ello
w
) *2
Emitter
Recei
v
er
Safety controller
*3 *4
*5
F39-JGR3K-L
F39-JG A-L
Timing chart
Beam state: Unblocked
Blocked
Reset switch (S2)
Test switch (S1)
OSSD
S1: Test s w itch
S2: Locko u t/interlock reset s w itch
L1: Lamp

: Indicates a switch position.
Function
Setting
DIP switch SD Manager 3
EDM EDM Disabled (factory default setting) [EDM]: Disabled
Interlock *6 Manual Reset [Start interlock] : Enable
[Restart interlock] : Enable
Operating Range Selection Long : Open the OPERATING RANGE SELECT INPUT line of the emitter or connect the line to 24 VDC.
Non-Muting system Perform wiring according to the wiring diagram.
N/A [Muting] : Disable *6
External Test used *9 Connect the TEST line of the emitter to 24V/0V of the emitter via a test switch (NO contact).
*
7
N/A [External test signal inversion] : Disable
Optical Synchronization Open the COM(+) and COM(-) lines of the emitter.
㻠 㻻㻺
㻡 㻻㻺
*1. Reverse the polarity of the power supply when using in the NPN system.
Select a safety controller of PNP or NPN type according to the system of your
application.
*2. Connect the line to 0 VDC if F3SG-SR or F3SG-PGA-L is used in Short
Mode.F3SG-PGA-A/-C does not support the Operating Range Selection
function.
*3. Refer to 6-3. Connectable Safety Control Units for more information.
*4. The safety controller and the F3SG-SR/PG must share the power supply or
be connected to the common terminal of the power supply.
*5. This is the case for a PELV circuit.
*6. Set the function with the DIP Switches on the Intelligent Tap or the SD
Manager 3, restore the settings to the F3SG-SR/PG, and perform wiring
according to the wiring diagram.
*7. This wiring example shows light emission stop when connected to 24 VDC
with PNP setting, and light emission stop when connected to 0 VDC with NPN
setting. If TEST switch is not needed, refer to
2-6. External Test .
*8. To use F3SG-PGA-C, wire the receiver side of the emitter/receiver of F3SG-
PGA-C as shown in the above figure. Wiring of the emitter side is not needed.
*9. F3SG-PGA-C does not support the External Test function.
Intelligent Tap Needed