Omron F3SG-PG Series, Руководство пользователя, Страница: 416 / 473

386
Chapter
6
Wiring Exa
m
p
le
s
(f
or F3
SG-SR/PG)
F3SG-SR/PG
User’s Manual
Input/Output Circuit and Applications
6-2-1-3. Auto Reset Mode with Optical Synchronization and EDM Used
[Wiring Example (F3SG-SR and F3SG-PGA-A/-L*6)]
When a functional earth is necessary, wire an earth cable according to the example in
6-2-1-1. Auto Reset Mode with Optical
Synchronization and EDM Unused
. Also refer to 5-4-4. Functional Earth Connection for more information.
F3SG-SRA

F3SG-PGA-A/-L

F3SG-SRB

F3SG-PGA-C

*6
KM1 KM2
24 V DC
W iring for N P N *1
*4
24 V DC
KM1
KM2
S1
KM1
KM2
M
S1: Locko u t reset s w itch
KM1, KM2: Safety relay w ith forci b ly g u ided contacts (G7SA) or magnetic contactor
M: Motor
Recei
v
er
Emitter
OSSD 1 (Black) OSSD 2 (
W
hite)
24
V
/0
V
(Bro
w
n)
OPERATI
N
G RA
N
GE
SELECT I
N
PUT (Yello
w
) *2
TEST (Black) *3 N
ot
u
sed (
W
hite)
24
V
/0
V
(Bro
w
n)
0
V
/24
V
(Bl
u
e)
0
V
/24
V
(Bl
u
e)
AUX (Red) MUTE B (Pink) MUTE A (Gray)
RESET/EDM (Y
ello
w
)
Beam state: Un b locked
Blocked
OSSD
Timing chart
F39-JGR3K-L
F39-JG A-L
F39-JGR3K-D
F39-JG A-D
*1. Reverse the polarity of the power supply when using in the NPN system.
*2. Connect the line to 0 VDC if F3SG-SR or F3SG-PGA-L is used in Short Mode.
F3SG-PGA-A/-C does not support the Operating Range Selection function.
*3. Refer to 2-6. External Test for more information if External Test is used.
*4. This is the case for a PELV circuit.
*5. Set the function with the DIP Switches on the Intelligent Tap or the SD Manager 3,
restore the settings to the F3SG-SR/PG, and perform wiring according to the
wiring diagram.
*6. To use F3SG-PGA-C, wire the receiver side of the emitter/receiver of F3SG-PGA-
C as shown in the above figure. Wiring of the emitter side is not needed.

: Indicates a switch position.
Function
Setting
DIP switch SD Manager 3
EDM *5 EDM Enabled [External device monitoring] : Enable
Interlock Auto Reset (factory default setting)
Operating Range Selection Long : Open the OPERATING RANGE SELECT INPUT line of the emitter or connect the line to 24 VDC.
Non-Muting system Perform wiring according to the wiring diagram.
N/A [Muting] : Disable
External Test not used Connect the TEST line of the emitter to 0V/24V of the emitter.
Optical Synchronization Do not connect the COM(+) and COM(-) lines of the of emitter and receiver with each other.
㻟 㻻㻺
Intelligent Tap Needed