![background image](http://html.mh-extra.com/html/omron/e5ewl/e5ewl_instruction-manual_744355001.webp)
E5EWL
Temperature Controller
Instruction Manual
Thank you for purchasing the OMRON E5EWL Temperature
Controller. This manual describes the functions, performance,
and application methods needed for optimum use of the
product.
Please observe the following items when using the product.
Ŗ 6JKURTQFWEVKUFGUKIPGFHQTWUGD[SWCNKHKGFRGTUQPPGNYKVJC
knowledge of electrical systems.
Ŗ $GHQTG WUKPI VJG RTQFWEV VJQTQWIJN[ TGCF CPF WPFGTUVCPF
this manual to ensure correct use.
Ŗ -GGRVJKUOCPWCNKPCUCHGNQECVKQPUQVJCVKVKUCXCKNCDNGHQT
TGHGTGPEGYJGPGXGTTGSWKTGF
©
All Rights Reserved
Suitability for Use
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination
of the products in the customer's application or use of the product. Take all necessary steps to determine the suitability
QHVJGRTQFWEVHQTVJGU[UVGOUOCEJKPGUCPFGSWKROGPVYKVJYJKEJKVYKNNDGWUGF
-PQYCPFQDUGTXGCNNRTQJKDKVKQPUQHWUGCRRNKECDNGVQVJKURTQFWEV
0'8'4 75' 6*' 241&7%65 (14 #0 #22.+%#6+10 +081.8+0) 5'4+175 4+5- 61 .+(' 14 2412'46;
9+6*176'0574+0)6*#66*'5;56'/#5#9*1.'*#5$''0&'5+)0'&61#&&4'556*'4+5-5#0&
6*#66*'1/410241&7%6+52412'4.;4#6'�&+056#..'&(146*'+06'0&'&75'9+6*+06*'
18'4#..'37+2/'06145;56'/
See also product catalog for Warranty and Limitation of Liability.
CAUTION
Do not touch the terminals while power is being supplied.
Doing so may occasionally result in minor injury due to electric shock.
Do not allow pieces of metal, wire clippings, or fine metallic shavings or filings from installation to enter the
product. Doing so may occasionally result in electric shock, fire, or malfunction.
Do not use the product where subject to flammable or explosive gas. Otherwise, minor injury from explosion may
occasionally occur.
Never disassemble, modify, or repair the product or touch any of the internal parts. Minor electric shock, fire, or
malfunction may occasionally occur.
If the output relays are used past their life expectancy, contact fusing or burning may occasionally occur. Always
consider the application conditions and use the output relays within their rated load and electrical life expectancy.
The life expectancy of output relays varies considerably with the output load and switching conditions.
Tighten the terminal screws to between 0.74 and 0.90 N·m. Loose screws may occasionally result in fire.
Set the parameters of the product so that they are suitable for the system being controlled. If they are not
suitable, unexpected operation may occasionally result in property damage or accidents.
EN
R
Relay output: 250 VAC, 3 A
Q
Voltage output (for driving SSR): 12 VDC, 21 mA
Control output
1
Sensor type
3
1
One relay output: 250 VAC, 1 A (resistive load)
2
E5EWL-
1 2 3
Ŗ
Insert the mounting brackets into the fixing slots located on the top and bottom of
the rear case. Push the adapter on from the rear to secure the Controller.
Ŗ
Make sure that the surrounding temperature does not exceed the allowable
operating temperature given in the specifications, especially when two or more
Controllers are mounted.
Ŗ
The voltage output (control output) is not electrically isolated from the internal
wiring. One or the other of the control output terminals must therefore be left
ungrounded when using a grounded thermocouple thermometer. (If both are
grounded, measurements will be unreliable due to sneak current.)
Individual Mounting
Side-by-side Mounting
6%
6JGTOQEQWRNG-,64QT5
P
Platinum resistance thermometer (Pt100)
6JGUVCPFD[UGSWGPEGKUENGCTGFYJGPVJGCNCTO1((EQPFKVKQPJCUDGGPOGV
6JGUVCPFD[UGSWGPEGKUUVCTVGFCICKPYJGPCP[QHVJGHQNNQYKPIEQPFKVKQPUKUOGV
Ŗ
Operation is started (power is turned ON or operation is switched from stop to run).
Ŗ
The alarm value is changed.
Ŗ
The temperature input offset is changed.
Ŗ
The set point is changed.
5VCPFD[UGSWGPEGENGCTGF
Alarm value
#NCTOYKVJUVCPFD[UGSWGPEG
Process value
Time
#NCTOYKVJQWVUVCPFD[UGSWGPEG
'ZCORNG&GXKCVKQP.QYGT.KOKV5VCPFD[5GSWGPEG10
The default alarm type is 2.
Ŗ
The control output and the alarm output will turn OFF when an error occurs.
(For
s.err
, the alarm output will be processed for a high temperature error.)
Ŗ
If the input value exceeds the display limit (-1999 to 9999) but it is still within the control range,
[[[[
will be displayed for values under -1999.
Under these conditions, the control output and alarm output will operate normally.
*1: This error is displayed only when the process value and set point are displayed.
*2: If the display does not change, the Controller needs to be repaired.
If operation returns to normal, then noise may have caused the problem. Check for noise.
*3: On the E5EWL,
e111
will be displayed on display No. 1 and
sum
will be displayed on display No. 2.
The default input type is 8.
The default input type is 0.
300 to 2300
0.0 to 900.0
100 to 1500
0.0 to 750.0
300 to 700
199.9 to 700.0
0 to 3000
0 to 3000
200 to 1300
20.0 to 500.0
100 to 850
20.0 to 400.0
200 to 400
199.9 to 400.0
0 to 1700
0 to 1700
Input
Setting range (°C)
Setting range (°F)
t
-
n
i
l.adj
t
p
a
o
Input Type
inpt
at
AT Execute/
Cancel
d-u
Temperature
Unit
s
n
i
t
p
k
o
Temperature
Input Shift
cntl
PID
Ŗ
ON/OFF
al-1
Alarm Value1
p
Proportional
$CPF
cp
Control Period
r-s
RUN/STOP
i
Integral Time
oreV
Direct/Reverse
Operation
d
Derivative
Time
alt1
Alarm1 Type
of-r
hys
Hysteresis
Operation/
Adjustment
Protect
Initial
Setting
Protect
Operation
%QPVTQN-G[
Protect
Manual Reset
Value
Adjustment
Level
for less
for at least
3 seconds.
Protect
Level
Operation
Level
+
Adjustment
Level
POWER ON
Initial Setting
Level
100 to 240 VAC, 50/60 Hz
85% to 110% of the rated voltage
Relay output: 250 VAC, 3 A (resistive load)
Voltage output (for driving SSR): 12 VDC
+25%/
15%, 21 mA
Relay outputs: 250 VAC, 1 A (resistive load)
ON/OFF or 2-PID control
100,000 operations
250 ms
ŦVQu%YKVJPQHTGG\KPIQTEQPFGPUCVKQP
6JGTOQEQWRNG-,64QT5
,+5%CPF+'%
Platinum resistance thermometer: Pt100
,+5%CPF+'%
Control output
Recommended fuse
Weight
Degree of protection
Alarm output
Control method
Electrical life of relay
Sampling period
Malfunction vibration
Vibration resistance
Ambient temperature
Ambient humidity
Storage temperature
Altitude
Installation environment
Memory protection
Indication accuracy
(ambient temperature: 23°C)
25% to 85%
Power supply voltage
Operating voltage range
Power consumption
ŦVQu%YKVJPQHTGG\KPIQTEQPFGPUCVKQP
2,000 m max.
T2A, 250 VAC, time-lag, low-breaking capacity
Approx. 150 g (Controller only)
Front panel: IP50, Rear case: IP20,
Terminal section: IP00
Installation category II,
pollution degree 2 (as per IEC 61010-1)
Non-volatile memory
(number of write operations: 100,000)
Sensor type
Alarm
type
No alarm
Deviation upper/lower limit
Deviation upper limit
Deviation lower limit
Deviation upper/lower range
Deviation upper/lower limit
UVCPFD[UGSWGPEG10
Deviation upper limit standby
UGSWGPEG10
Deviation lower limit standby
UGSWGPEG10
Absolute value upper limit
Absolute value lower limit
Absolute value upper limit
UVCPFD[UGSWGPEG10
Absolute value lower limit
UVCPFD[UGSWGPEG10
Do not set.
Output OFF
Positive alarm
value (X)
Negative alarm
value (X)
Always ON
Always OFF
Always OFF
Process value
Level
Setting
Adjustment Level
Operation
Level
PV/SP
Others (Alarm Value)
: Operation control keys are enabled but operation control using
parameters is disabled.
: Operation control keys are disabled but operation control using
parameters is enabled.
: Operation control keys and operation control using parameters
are disabled.
Default: 0
Operation Control
AT Execute/Cancel (
M
+
D
)
RUN/STOP (
M
+
U
)
0
1
2
3
4
Setting
Level
1
0
Do not set.
2
Setting
Initial Setting Level
Default: 1
Ŗ
Operation/Adjustment Protection
Ŗ
Initial Setting Protection
Ŗ1RGTCVKQP%QPVTQN-G[2TQVGEVKQP
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
Step 3
Adjustment Level: Used to tune parameters and set control parameters.
Adjustment Level
AT Execute/Cancel
Temperature Input Shift
2TQRQTVKQPCN$CPF
Integral Time
Derivative Time
Manual Reset Value
Hysteresis
l.adj
at
ins
p
i
d
of-r
hys
This display indicates that you have moved to Adjustment Level.
Starts and stops autotuning. (Displayed only when PID control is selected.)
*1*2
Set a compensation value for the temperature input in increments of 0.1°C or 0.1°F.
Set the proportional band in increments of 0.1°C or 0.1°F.(Displayed only when PID control is selected.)
Set the integral time in increments of 1 s. (Displayed only when PID control is selected.)
Set the derivative time in increments of 1 s. (Displayed only when PID control is selected.)
Set the manipulated value to use for P or PD control (I = 0). The offset will be canceled.
Set the hysteresis to use to achieve stable operation when switching the control output
ON/OFF during ON/OFF control. (Displayed only when ON/OFF control is selected.)
off
/
on
-199.9
to
999.9
0.1
to
999.9
0
to
3999
0
to
3999
0.0
to
100.0
0.1
to
999.9
OFF
0.0 (°C)
8.0 (°C)
233 (s)
40 (s)
50.0 (%)
1.0 (°C)
Step 4
Protect Level: Used to set parameters to restrict key operations.
Operation/Adjustment Protect
Initial Setting Protect
1RGTCVKQP%QPVTQN-G[2TQVGEV
oapt
inpt
okpt
Set protection for Operation Level and Adjustment Level.
Set protection for Initial Setting Level.
5GVRTQVGEVKQPHQTVJG#6-G[CPF4705612-G[QRGTCVKQPEQPVTQNMG[U
*Refer to table on the right.
*Refer to table on the right.
*Refer to table on the right.
0
1
0
Step 2
Operation Level: Used to monitor the process value and to set the set point, alarm value, etc.
PV/SP
Alarm value1
Alarm value2
Monitor the process value and set the set point.
Set the alarm value. The location of the decimal point depends on the input type.
Set the alarm value. The location of the decimal point depends on the input type.
-1999
to
9999
-1999
to
9999
SV: 0 (°C)
0 (°C)
0 (°C)
Display
Parameter name
Description
Setting/monitoring range
Default
Step 1
Initial Setting Level: Used to set basic specifications.
Input Type
Temperature Unit
PID
Ŗ
ON/OFF
Control Period
Direct/Reverse Operation
Alarm1 Type
in-t
d-u
cntl
cp
orev
alt1
Set the input sensor type.
Set the unit for temperature input to Celsius (°C) or Fahrenheit (°F).
Set either 2-PID control or ON/OFF control.
Set the time-proportional control period for the control output.
(Displayed only when PID control is selected.)
Set either reverse option (heating control) or direct operation (cooling control).
Set the alarm type.
c
(°C)/
f
(°F)
onof
/
pid
0.5
,
1
to
99
0 or 8
°C
ON/OFF
20 or 2 (s)
Or-r
(reverse control)
2 (Deviation upper limit)
or-r
(reverse control)
or-d
(direct control)
&KURNC[GFQPN[YJGP1RGTCVKQP%QPVTQN-G[2TQVGEVKQPKUUGVVQ
*2: The setting cannot be changed during autotuning. Autotuning will be stopped if you move to Initial Setting Level or stop control operation.
Ŗ
Displays during Autotuning
E5EWL: The AT Execute/Cancel characters on display No. 1 and the PV/SP characters on display No. 2 will flash.
-
,
T
R
S
Setting
0
1
2
3
4
5
6
7
Check the wiring of inputs, disconnections, short circuits
and input type.
Turn the power OFF then back ON again.
*2
Press the
U
and
D
-G[UHQTCVNGCUVUGEQPFUVQ
initialize the settings and clear the non-volatile memory error
.
Display
Action
s.err
(S.ERR)
e111
(E111)
e111
/
sum
(E111)/(SUM)
*3
Meaning
Input error
*1
RAM memory error
Non-volatile memory
memory error
300 to 1500
199.9 to 900.0
200 to 850
199.9 to 500.0
Pt100
8
9
Safety Precautions
Indicates a potentially hazardous situation which, if not avoided, is
likely to result in minor or moderate injury or property damage. Read
this manual carefully before using the product.
CAUTION
Package Contents
Ŗ6GORGTCVWTG%QPVTQNNGT
Ŗ#FCRVGT
Ŗ+PUVTWEVKQP/CPWCN
Adapter
Ŗ
Solderless terminal size: M3.5
Ŗ
Terminal Cover: E53-COV19
(sold separately)
(8)
D
&QYP-G[4GFWEGUVJGUGVVKPI
(9)
U
7R-G[+PETGCUGUVJGUGVVKPI
(10)
+
M
Press these keys for at least 3 seconds in Operation Level or Adjustment Level to go to Protect Level.
Press these keys for at least 1 second in Protect Level to return to Operation Level.
(11)
M
+
D
Press these keys for at least 2 seconds to start or stop autotuning.*1
(12)
M
+
U
Press these keys for at least 2 seconds to start or stop operation.*2
*1: These keys are disabled when starting and stopping autotuning has been disabled with operation control key protection.
*2: These keys are disabled when starting and stopping operation has been disabled with operation control key protection.
Control Output
Ŗ
Relay output: 250 VAC, 3 A (resistive load)
Ŗ
Voltage output (for driving SSR): 12 VDC, 21 mA
Alarm hysteresis
(always 0.2
q
C/
q
F)
OMRON CORPORATION
-G[VQ9CTPKPI5[ODQNU
Warning Symbols
Specifications
Wiring
Model Number Legends
Dimensions (mm)
Installation (mm)
Connections
Front Panel Part Names and Functions
(1) Display No. 1
Displays the process value (PV) or parameter.
(2) Display No. 2
Displays the set point (SP) or parameter setting.
(3) ALM1(ALM2)
Lit while the alarm1(alarm2) is ON. Not lit while the alarm is OFF.
(4) OUT
Lit while the control output is ON. Not lit while the control output is OFF.
(5) STOP
Not lit during operation. Lit while operation is stopped.
.GXGN-G[%JCPIGUVJGUGVVKPINGXGN
(7)
M
/QFG-G[%JCPIGUVJGRCTCOGVGTYKVJKPVJGUGVVKPINGXGN
Operation Menu
Parameter Operations
Press
Press
than 1 second.
for at least 1 second.
Press
Parameter Tables
Display
Parameter name
Description
Setting/monitoring range
Default
Display
Parameter name
Description
Setting/monitoring range
Default
Display
Parameter name
Description
Setting/monitoring range
Default
*Refer to table on the right.
*Refer to table on the right.
al-1
al-2
Input type: Thermocouple
Input
Setting range (°C)
Setting range (°F)
Setting
Input type: Platinum Resistance Thermometer
Troubleshooting
Protection
: Can be displayed and changed.
: Can only be displayed.
: Display or changing to another level is not possible.
0
1
2
3
OMRON EUROPE B.V.
Wegalaan 67-69, NL-2132 JD Hoofddorp The Netherlands
Phone 31-2356-81-300
FAX 31-2356-81-388
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg, IL 60173-5302 U.S.A
Phone 1-847-843-7900
FAX 1-847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark, Singapore 119967
Phone 65-6835-3011
FAX 65-6835-2711
OMRON Corporation
Shiokoji Horikawa, Shimogyo-ku, Kyoto 600-8530 JAPAN
Malfunction shock
Shock resistance
10 to 55 Hz, 20 m/s
2
HQTOKPGCEJKP:;CPF<FKTGEVKQPU
10 to 55 Hz, 20 m/s
2
HQTJGCEJKP:;CPF<FKTGEVKQPU
100 m/s
2
VKOGUGCEJKP:;CPF<FKTGEVKQPU
300 m/s
2
VKOGUGCEJKP:;CPF<FKTGEVKQPU
(
r
0.5% of indication value or
r
1
q
C, whichever is greater)
r
1 digit max.
R, S thermocouple at 200
q
C or less:
r
3
q
C
r
1 digit max.
-6VJGTOQEQWRNGCV
100
q
C or less:
r
2
q
C
r
1 digit max.
Use a deviation alarm to link the alarm to the SP.
If the SP is changed, the alarm operating point will also change.
Deviation Alarm
Use an absolute value alarm when the alarm is not linked to the SP.
Absolute Value Alarm
0
X
ON
OFF
SP
X
ON
OFF
SP
X
ON
OFF
SP
X
ON
OFF
0
X
ON
OFF
0
X
ON
OFF
0
X
ON
OFF
0
X
ON
OFF
ON
OFF
SP
X
X
SP
X
ON
OFF
SP
X
ON
OFF
SP
X
X
ON
OFF
SP
X
X
ON
OFF
SP
X
ON
OFF
SP
X
ON
OFF
0
X
ON
OFF
0
X
ON
OFF
0
X
ON
OFF
Set this difference.
SP
Linked
Fixed
Set the difference
(deviation) from the SP.
Set the alarm operating point as the temperature (absolute value).
Set the temperature (absolute value)
at which to output an alarm.
0
#NCTOUYKVJC5VCPFD[5GSWGPEG
SP
X
ON
OFF
Alarms
Setting
0
1
2
3
4
5
6
7
8
9
10
11
12
Alarm
operating
point
Alarm
operating
point
The alarm is blocked until the first safe-state is reached.
Unwanted alarm during start-up are prevented.
Deviation/ab
solute value
alarm
Deviation
alarm
Deviation
alarm
Deviation
alarm
Deviation
alarm
Deviation
alarm
Deviation
alarm
Deviation
alarm
Absolute
value alarm
Absolute
value alarm
Absolute
value alarm
Absolute
value alarm
Be sure to observe the following precautions to prevent operation failure, malfunction, or adverse affects on
the performance and functions of the product. Not doing so may occasionally result in unexpected events.
(1) The product is designed for indoor use only. Do not use the product outdoors or in any of the following
locations.
Places directly subject to heat radiated from heating equipment.
Places subject to splashing liquid or oil atmosphere.
Places subject to direct sunlight.
Places subject to dust or corrosive gas (in particular, sulfide gas and ammonia gas).
Places subject to intense temperature change.
Places subject to icing and condensation.
Places subject to vibration and large shocks.
(2) Use/store within the rated temperature and humidity ranges.
Provide forced-cooling if required.
(3) To allow heat to escape, do not block the area around the product.
Do not block the ventilation holes on the product.
(4) Be sure to wire properly with correct polarity of terminals.
(5) Use specified size (M3.5, width 7.2 mm or less) crimped terminals for wiring. To connect bare wires to
the terminal block, use copper braided or solid wires with a rated temperature of over 70
°C
and a
gauge of AWG24 to AWG14 (equal to a cross-sectional area of 0.205 to 2.081 mm
2
). (The stripping
length is 5 to 6 mm.) Up to two wires of same size and type, or two crimped terminals can be inserted
into a single terminal.
(6) Do not wire the terminals which are not used.
(7) Allow as much space as possible between the controller and devices that generate a powerful high-
frequency or surge.
Separate the high-voltage or large-current power lines from other lines, and avoid parallel or common
wiring with the power lines when you are wiring to the terminals.
(8) Use this product within the rated load and power supply.
(9) Make sure that the rated voltage is attained within two seconds of turning ON the power using a switch
or relay contact. If the voltage is applied gradually, the power may not be reset or output malfunctions
may occur.
(10) Make sure that the Controller has 30 minutes or more to warm up after turning ON the power before
starting actual control operations to ensure the correct temperature display.
(11) A switch or circuit breaker should be provided close to this unit.
The switch or circuit breaker should be within easy reach of the operator, and must be marked as a
disconnecting means for this unit.
(12) Do not use paint thinner or similar chemical to clean with. Use standard grade alcohol.
(13) Design system (control panel, etc) considering the 2 second of delay that the controller’s output to be
set after power ON.
(14) The output may turn OFF when shifting to certain levels. Take this into consideration when performing
control.
(15) The number of non-volatile memory write operations is limited.
Precautions for Safe Use
A malfunction in the Temperature Controller may occasionally make control operations impossible or prevent
alarm outputs, resulting in property damage. To maintain safety in the event of malfunction of the Temperature
Controller, take appropriate safety measures, such as installing a monitoring device on a separate line.
Default: 0
: Can be displayed and changed.
: Display or changing to another level is not possible.
2266757-7A
EL2
for at least 3 seconds.
Press
for at least
1 second.
+
Press
Pt input
Alarm1 Output
Ŗ4GNC[QWVRWV8#%#
(resistive load)
Input power supply:
100 to 240 VAC,
50/60 Hz
DO NOT USE
TC input
ˇ
ˉ
A
$
$
ˇ
ˉ
1
2
3
4
7
8
9
10
6
Control output
25
0
3963
Conformance to EN/IEC Standards
This is a class A product.In residential areas it may cause radio interference,
KPYJKEJECUGVJGWUGTOC[DGTGSWKTGFVQVCMGCFGSWCVGOGCUWTGUVQTGFWEGKPVGTHGTGPEG
Recommended panel thickness is 1 to 5 mm.
˄˅
˄˅
˄˅
˄˅
˄˅
˄˅
˄˅
˄˅
˄˅
E5EWL
˄˅˄˅
˄˅
OUT
STOP
ALM1
(48 x n
WODGTQH%QPVTQNNGTUŦ
Alarm
92
+0.8
0
120 min.
+1.0
0
45
+0.6
0
92
+0.8
0
96
48
4
60
51.5
44
91.1
110
*2
2
Two relay outputs: 250 VAC, 1 A (resistive load)
5
Alarm2 Output
Ŗ4GNC[QWVRWV8#%#
(resistive load)
ALM2
al-2
Alarm Value2
M
*Refer to table on the right. 2 (Deviation upper limit)
Set the alarm type.
alt2
Alarm2 Type
RUN/STOP
Start and stop control operation.
*1
run
/
stop
RUN
r-s
alt2
Alarm2 Type
M
Approx. 3.5VA(One alarm)
Approx. 4.2VA(Two alarms)