Omron E5CC-T Скачать руководство пользователя

Страница: 156 / 186

6 Programless Communications

6 - 40



C-T Digital Temperature Controllers Programmable Type Communications Manual (H186)

6-6

Connecting to MELSEC Q-series
PLCs

The following configuration is used as an example in giving the setup and application procedures for

programless communications.

•

All of the E5CC-T Controllers must be the same model. (Copying parameter settings is not possible if

the models are different.)

•

D0 to D209 are used in the PLC memory. The default E5CC-T parameter allocations are used.

•

A commercially available USB2.0, A/B cable is used.

Note: Refer to the

GX Works2 Installation Instructions

(BCN-P5713 ) for information on installing the GX Works2

and to the

GX Works2 Version 1 Operating Manual (Common)

(SH-080779ENG) for information on installing

the USB driver.

The application procedure is given below.

6-6-1

Configuration and Procedure

E5CC-T

o.0

E5CC-T

o.1

E5CC-T

o.2

RS-4

USB port

USB connector

IBM PC/AT or compati

QJ71C24

-R4

CPU

orks2

Programming
Soft

are

Commercially
a

aila

le USB

START

ire the net

ork.

ire the QJ71C24

-R4 to the E5CC-T Controllers.

C-T Controller Set

Set

p programless comm

nications in the E5CC-T Controllers.

Check operation.

Use GX

orks2 to confirm that programless comm

nications are operating.

Set

p the PLC.

Use GX

orks2 to set

p comm

nications on the QJ71C24

-R4-

1 to ena

comm

nicating

ith the E5CC-T Controllers.

Содержание E5CC-T



























































































































































































Результаты поиска

Содержание E5CC-T

Отзывы:

Похожие инструкции для E5CC-T

Бренды по названию

Популярные бренды

Omron E5CC-T, Руководство по связи

Результаты поиска

Содержание E5CC-T

Отзывы:

Похожие инструкции для E5CC-T

Бренды по названию

Популярные бренды