;&'4&'-0)*'")<
Section 3-5
**
Updating Unit Output
Pattern with Preset or Reset
Action
Besides by crossing CV’s the Unit Output Pattern can also be updated by a Preset
or a Reset action. To trigger a Preset or Reset action refer to
and 3-6
. Every Preset or Reset Action will then update
the Unit Output Pattern according to the predefined Output Set and Output Reset
Patterns. You can define an Output to be Set, Reset or remain Unchanged (similar
as on reaching a Comparison Value).
Note
In case for a Preset or Reset action for a specific Output both a Set and a Reset
is defined the Reset has priority.
3-5-3
Manual Output Control
Manual or Automatic
Control
The Digital Outputs of the High-speed Counter Unit can be controlled automati-
cally or manually. Automatic control of the Digital Outputs results in the automatic
update of the Unit Output Pattern. The Unit Output Pattern will then be updated
according to the Mode for which the Unit is configured (Range Mode or Compar-
ison Mode). By default (=0) the Unit is configured for Automatic Output Control.
To control the Physical Outputs (0-3) manually, Manual Output Control must be
selected by setting the Automatic/Manual Output Control Bit to 1. Now it is possi-
ble to force ON and OFF the Physical Digital Outputs by setting and resetting the
corresponding bits respectively. Manual Output Control can be used for test pur-
poses (wiring) when the Unit is being installed.
Bits 0, 1, 2 and 3 correspond to the Physical Digital Outputs O0, O1, O2 and O3
CNT1:
CNT2:
CNT3:
CNT4:
m+59
m+104
m+149
m+194
15 14 13 12 11 10 9
7
7
6
5
4 O3 O2 O1 O0
m+60
m+105
m+150
m+195
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
Output Set Pattern
m+61
m+106
m+151
m+196
15 14 13 12 11 10 9
7
7
6
5
4 O3 O2 O1 O0
m+62
m+107
m+152
m+197
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
Output Reset Pattern
= Digital Outputs 0-3
(corresponding with Physical Digital Outputs O0, O1, O2 and O3)
= Soft Outputs 4-31
On triggering a Preset or Reset action:
Output Set Pattern:
Output Reset Pattern:
0 = No Change
1 = Set Output
0 = No Change
1 = Reset Output
8
8
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
General Setting:
n
Manual Output Control:
0 = Force Output OFF
1 = Force Output ON
Selection Automatic/Manual:
0 = Automatic Output Control
1 = Manual Output Control
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
W902-E2-03.book Seite 77 Donnerstag, 7. Oktober 2004 2:06 14
Содержание CS1W-CT021
