Omron Cobra 350 CR/ESD Скачать руководство пользователя | Manualshive

Страница: 112 / 138

background image

112

Cobra 350 User's Guide

05624-000 Rev. K

8.9 Commissioning a System with an eMB-40R

l

If the system will not power up, and the robot status display shows SE, you need to
commission the system.

l

If the system will not power up in Manual mode, and the robot status display shows
TR, you need to commission the system.

Safety Commissioning Utilities

The eMB-40R adds two functions that implement safety in hardware:

l

E-Stop

This serves as a backup to the standard software E-Stop process. The system will
always try to stop the robot using the software E-Stop first. The hardware E-Stop will
take over in the event of a failure of the software E-Stop.

l

Teach Restrict

This limits the maximum speed of the robot when it is operated in Manual mode. As
with the E-Stop, this is a hardware backup to software limits on robot speed. If the soft-
ware fails to limit the robot speed during manual operation, the hardware Teach
Restrict will disable power to the system.

These two functions are only in the eMB-40R amplifiers. They were not implemented in hard-
ware in the MB-40R amplifiers, so these utilities do not apply to those amplifiers.

These two functions are supported by four wizards:

l

E-Stop Configuration

This sets the E-Stop hardware delay to factory specifications.

l

E-Stop Verification

This verifies that the hardware E-Stop is functioning correctly.

l

Teach Restrict Configuration

This sets the hardware Teach Restrict maximum speed to factory specifications.

l

Teach Restrict Verification

This verifies that the hardware Teach Restrict is functioning correctly.

The initial utility screen will tell you which functions are commissioned. If a function is not
commissioned, its verification wizard will not be displayed. Any displayed verification wizard
can be run at any time, to ensure that its function is working properly.

Prerequisites

l

The robot must be set up and functional.

l

The robot must use eMB-40R amplifiers.

The MB-40R amplifiers do not support these hardware functions, and these wizards
will not run.

l

ACE software must be installed.

l

The Front Panel keyswitch must be in Auto mode.

«
...
110
111
112
113
114
...
»

Содержание Cobra 350 CR/ESD











































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cobra 350 CR/ESD

Бренд: Pololu Страницы: 97

Бренд: AC Air Technology Страницы: 33

Бренд: SuperDroid Robots Страницы: 9

Бренд: EasyRobotics Страницы: 38

Бренд: Robotnik Страницы: 19

Бренд: Hanwha Страницы: 195

Match LWR50L-21 Series

Бренд: Zimmer Страницы: 53

Бренд: Waveshare Страницы: 6

Medium & Heavy Payload Series

Бренд: Omron Страницы: 68

Бренд: Unitree Страницы: 45

Бренд: Wido Страницы: 4

Бренд: Vex Robotics Страницы: 8

Бренд: Vex Robotics Страницы: 44

Бренд: Playknowlogy Страницы: 38

Бренд: Blue Robotics Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды