manualshive.com logo in svg

Omnitracs Trailer Tracks 150, Инструкция по установке и устранению неисправностей

Поделиться
Скачать
Omnitracs Trailer Tracks 150 Скачать руководство пользователя страница 9

80-J7616-1 Rev. C 

MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION

 

9 

 

2)

 

TT150

 

System Component Overview 

TT150 Components 

TT150 Terminal 

TT150 terminal with microprocessor, cellular modem, rechargeable internal battery pack, 
cellular antenna, and GPS antenna. Attached to the terminal is a cable for recharging the 
TT150 battery pack when the trailer is connected to a tractor. 

The terminal is designed according to industry environmental specifications. The system 
allows over-the-air (OTA) reprogramming of the terminal’s on-board firmware. 

The TT150 terminal also has two LEDs for verifying cellular coverage and a GPS fix when 
active. 

The trailer operator (truck driver, loader, or unloader) does not need to access the terminal. 
It should be mounted in a safe and secure place on the trailer. 

Internal TT150 Battery 

Internal to the TT150 terminal housing is a lithium ion rechargeable battery that is used 
when the trailer is not connected to external power (i.e. not connected to a tractor). A 
fully charged terminal will work for 90 days sending one message/position a day when 
not powered. The battery will recharge when power is applied to the 7-way. The battery 
is not serviceable. 

Note: The TT150 does not ship fully charged. It is recommended that the battery be 
fully charged immediately after it is installed to provide the best messaging experience. 

TT150 Power Cable Assembly 

The TT150 power cable assembly is permanently attached to the TT150 terminal enclosure. 
The power cable assembly contains fuse holders, which are separate from the power cable 
assembly to ease routing of the cable assembly and make installation of the TT150 terminal 
easier. 

Содержание Trailer Tracks 150





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды