OmniCell ERB Скачать руководство пользователя страница 70

Страница: 70 / 112

2-60

Installation Instructions

Installation on G4 Cabinets

External Return Bin Installation and Service Guide

/67-2038 Rev D

8. Close and lock the ERB access door.

Attaching the ERB in the Lower Position

1. Attach the

bracket

to the upper and lower mounting bars using four

8/32 flat head screws

2. Slide the assembly up to align the top of the bracket with the screws on the side of the AWS.

Figure 2-145.

Alignment of bracket in lower position

3. Use a 1/4” Allen key to tighten the

5/16” set screws

on both ends of each of the mounting bars.

4. Open the ERB access door with both keys. Use

key

#2204 to unlock the access door and

key

#2202 to override the solenoid.

Figure 2-146.

Access door and cam lock keys

5. Set the ERB on the bracket ledge, aligning the pins on the ledge to the holes in the bottom of

the ERB.

Figure 2-147.

ERB being set onto bracket ledge pins

Align

Содержание ERB

















































































































Результаты поиска

Содержание ERB

Отзывы:

Похожие инструкции для ERB

Бренды по названию

Популярные бренды

OmniCell ERB, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ERB

Отзывы:

Похожие инструкции для ERB

Бренды по названию

Популярные бренды