manualshive.com logo in svg

Omicron CMC 310, Руководство пользователя

Поделиться
Скачать
Omicron CMC 310 Скачать руководство пользователя страница 11

OMICRON

11

Test set overview

3.2.2

CURRENT OUTPUT

→ Section 4.4.2 "Current outputs" on page 22.

Each output is galvanically separated from all other connections of the 

CMC 310

. All current outputs are protected against open circuits, short 

circuits, overload, and overtemperature.

WARNING

Death or severe injury caused by dangerous inductive loads possible

If charged with current, inductive loads may store a dangerous amount of energy. For 
example, an energy of <350 mJ is considered safe according to the IEC 61010-1 safety 
standard.

► Make sure that the possibly stored energy of the inductive device under test is within 
safe limits.

► Do not use the 

CMC

 test set for the measurement on high inductances (power 

transformer, current transformer) due to the discharging processes.

► If in doubt, contact OMICRON Support for more information.

WARNING

Death or severe injury caused by dangerous voltage levels on conductive parts 
possible

Although the output voltages of the current generators are within touch-safe limits, the 
insulation to other input and output groups is implemented as functional insulation only. 
Therefore, the outputs can conduct dangerous voltages.

► Observe the wiring instructions and safety precautions given in section "Wiring" in the 
Safe use of CMC test sets manual.

► Do not touch open conductive parts with live current signals (e.g. blank screw 
terminals) while the 

CMC

 test set is switched on.

NOTICE

Equipment damage possible

An external infeed could damage or destroy the current output. The outputs are protected in switched-
off state by a short-circuit relay.

► Make sure that there is no infeed from an external source. 

Содержание CMC 310













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды