Olympus OmniScan MX2 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 228

Olympus OmniScan MX2 Скачать руководство пользователя страница 67

DMTA-20015-01EN [U8778402], Rev. J, January 2014

Specifications

55

5. Specifications

This chapter covers the OmniScan MX2 unit specifications. It includes the general
specifications for the instrument, in addition to the specifications applicable to alarms
and safety (see Table 10 on page 55 and T able 11 on page 59).

For the specifications applicable to specific acquisition modules, please refer to the
respective appendices at the end of this manual.

Table 10 OmniScan MX2 general specifications

Housing

Size

325 mm × 235 mm × 130 mm
(12.8 in. × 9.3 in. × 5.1 in.)

Weight

3.2 kg (7 lb) [no module and one
battery]
5 kg (11 lb) [with module and one
battery]

Environmental conditions

Operating
temperature

0 °C to 45 °C
–10 °C to 45 °C (with OMNI-M2
modules)

Storage temperature

–20 °C to 60 °C (with batteries inside)
–20 °C to 70 °C (with no batteries
inside)

«
...
65
66
67
68
69
...
»

Содержание OmniScan MX2





































































































































































































































Отзывы:

Нет отзывов