Olympus OmniScan MX2 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 228

Olympus OmniScan MX2 Скачать руководство пользователя страница 46

DMTA-20015-01EN [U8778402], Rev. J, January 2014

Chapter 2

34

To activate the auto-boot

1.

Turn off the OmniScan MX2 unit, remove the batteries, and then disconnect the
DC power adaptor.

2.

Press and hold the Power key (

).

3.

Connect the OmniScan MX2 to a DC power adaptor.

4.

Wait for the power indicator light to blink two times, and then release the Power

key (

).

5.

To deactivate the auto-boot, repeat steps 1 to 4.

2.4

Power Supply Management

The OmniScan MX2 is a portable instrument that can draw power from either
lithium-ion batteries or a DC power adaptor.

2.4.1

DC Power Adaptor

You can operate the OmniScan MX2 on AC power using the DC power adaptor (P/N:
OMNI-A-AC [U8767093]). The OMNI-A-AC has a universal AC power input, which
operates with any line voltage from 100 VAC to 120 VAC or from 200 VAC to
240 VAC, and at 50 Hz to 60 Hz line frequency.

To use AC power

1.

Connect the AC power cord to the DC power adaptor (P/N: OMNI-A-AC
[U8767093]) and to an appropriate power outlet.

Use only the AC power cord supplied with the OmniScan MX2. Do not use this AC
power cord with other products.

2.

On the right-hand side of the OmniScan MX2, lift the rubber seal covering the DC
adaptor connector plug (see Figure 2-4 on page 35).

«
...
44
45
46
47
48
...
»

Содержание OmniScan MX2





































































































































































































































Отзывы:

Нет отзывов