Olympus OmniScan MX2 Скачать руководство пользователя страница 161

Страница: 161 / 228

DMTA-20015-01EN [U8778402], Rev. J, January 2014

OMNI-M-PA1616 Module Specifications

149

F.2

Acquisition Specifications

This section details the acquisition specifications of frequency, data display, and
synchronization (see Table 45 on page 149).

Beam formation

Scan type

Sectorial and linear

Aperture

16 elements

Number of elements

16 elements

Number of focal laws

256

Delay range transmission 0 µs to 10 µs in 2.5 ns increments

Delay range reception

0 µs to 10 µs in 2.5 ns increments

Table 45 Acquisition specifications

Frequency

Digitizing frequency

100 MHz (10 bits)

A-scan (acquisition
mode)

Up to 6000 A-scans per second (512-point,
8-bit A-scan)

Maximum pulsing rate

Up to 10 kHz (C-scan)

Depth in material

59.8 meters in steel (longitudinal wave),
10 ms with compression
0.49 meter in steel (longitudinal wave),
81.9 µs without compression

Display

Refresh rate

A-scan: 60 Hz; S-scan: 20 Hz to 30 Hz

Envelope (echo-dynamic
mode)

Yes: Volume-corrected S-scan (30 Hz)

Synchronization

On internal clock

1 Hz to 10 kHz

External pace

Yes

On encoder

On 2 axes: from 1 to 65536 steps.

Table 44 Acoustic specifications

(continued)

Содержание OmniScan MX2





































































































































































































































Результаты поиска

Содержание OmniScan MX2

Отзывы:

Olympus OmniScan MX2, Руководство пользователя, Страница: 161 / 228

Результаты поиска

Содержание OmniScan MX2

Отзывы: