Olympus OmniScan MX2 Скачать руководство пользователя страница 153

Страница: 153 / 228

DMTA-20015-01EN [U8778402], Rev. J, January 2014

OMNI-M-UT-2C, OMNI-M-UT-4C, and OMNI-M-UT-8C Module Specifications

141

D.2

Acquisition Specifications

This section lists the acquisition specifications for frequency, data display, and
synchronization (see Table 39 on page 141).

D.3

Data Specifications

This section outlines the data specifications for processing, TCG, and storage (see
Table 40 on page 141).

Table 39 Acquisition specifications

Frequency

Digitizing frequency

100 MHz (10 bits)

A-scan (acquisition
mode)

Up to 6000 A-scans per second (512-point,
8-bit A-scan)

Maximum pulsing rate

Up to 10 kHz (C-scan)

Depth in material

59.8 meters in steel (L-wave), 10 ms with
compression
0.49 meter in steel (L-wave), 81.9 µs without
compression

Display

Refresh rate

A-scan: 60 Hz

Envelope (echo-dynamic
mode)

Yes

Synchronization

On internal clock

1 Hz to 10 kHz

External pace

Yes

On encoder

On 2 axes: from 1 to 65536 steps

Table 40 Data specifications

Processing

Number of data points

Up to 8000

Real-time averaging

2, 4, 8, 16

Rectification

RF, full wave, half wave+, half wave–

Содержание OmniScan MX2





































































































































































































































Результаты поиска

Содержание OmniScan MX2

Отзывы:

Olympus OmniScan MX2, Руководство пользователя, Страница: 153 / 228

Результаты поиска

Содержание OmniScan MX2

Отзывы: