Olympus OmniScan MX2 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 228

Olympus OmniScan MX2 Скачать руководство пользователя страница 113

DMTA-20015-01EN [U8778402], Rev. J, January 2014

Maintenance

101

9. Maintenance

This chapter describes the basic maintenance that must be performed on the
OmniScan MX unit by operators. The maintenance operations explained below enable
you to keep your instrument in good physical and working condition. By virtue of its
design, the OmniScan MX only requires minimal maintenance. The chapter covers
preventative maintenance and instrument cleaning.

9.1

Preventative Maintenance

The OmniScan MX does not have many moving parts, and therefore only requires
minimal preventative maintenance. Simply perform regular inspections to keep the
OmniScan MX in proper working order.

9.2

Instrument Cleaning

The OmniScan MX external surfaces (which includes the casing, the acquisition
module, and the LCD screen protector) may be cleaned as needed. This section
provides the appropriate procedure for cleaning the instrument.

9.2.1

Casing and Acquisition Module Cleaning

To clean the casing and acquisition module

1.

Make sure that the instrument is turned off, the power cord is disconnected, and
the batteries have been removed.

2.

Disconnect all cables and connectors, and make sure that all external ports on the
OmniScan MX have been covered with their rubber protectors.

«
...
111
112
113
114
115
...
»

Содержание OmniScan MX2





































































































































































































































Отзывы:

Нет отзывов