Olympus MV-1 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 18

Olympus MV-1 Скачать руководство пользователя страница 18

MV-1/MV-2 Endoscope Disinfectors

Frequently

Asked

Questions

09FQ0015 18/18

Two Corporate Center Drive, Melville, NY 11747

Copyright 2001, Olympus America Inc.

Copyright 2001 Olympus America Inc. This document and the contents contained herewith remain the property of Olympus America Inc. Reproduction of this document or any part

thereof by any means (electronic or otherwise) without the expressed written consent of Olympus America Inc. is strictly prohibited. Only printed copies with "Controlled Document -- Do

Not Copy" stamped in red are considered controlled copies. All other printed copies are considered Uncontrolled and may not contain the latest document revisions.

Troubleshooting: MV-1/MV-2 Control Panel (Cont’d)

#

Ensure the MV-1/MV-2 control panel is operating properly. If necessary, replace the MV-1/MV-2 control
panel.

#

Check the ribbon cables within the MV-1/MV-2 to be sure that they are connected properly and are not
loose.

Troubleshooting: Returning the Unit for Repair

If the MV-1/MV-2 Endoscope Disinfectors must be returned to Medivators, Inc. for repair or replacement,
contact Olympus by calling telephone # 1-800-848-9024. Choose the appropriate prompt for connection to
Medivators, Inc.

A “Hot Swap” will be performed, which means that Medivators, Inc. will provide the facility with a loaner unit to
replace the disabled MV-1/MV-2 until the unit is either repaired or replaced. Medivators, Inc. will provide
shipping instructions.

«
...
16
17
18

Содержание MV-1



















Отзывы:

Нет отзывов