Olympus MV-1 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 18

Olympus MV-1 Скачать руководство пользователя страница 17

MV-1/MV-2 Endoscope Disinfectors

Frequently

Asked

Questions

09FQ0015 17/18

Two Corporate Center Drive, Melville, NY 11747

Copyright 2001, Olympus America Inc.

Copyright 2001 Olympus America Inc. This document and the contents contained herewith remain the property of Olympus America Inc. Reproduction of this document or any part

thereof by any means (electronic or otherwise) without the expressed written consent of Olympus America Inc. is strictly prohibited. Only printed copies with "Controlled Document -- Do

Not Copy" stamped in red are considered controlled copies. All other printed copies are considered Uncontrolled and may not contain the latest document revisions.

Troubleshooting: Air/Water Flow (cont’d)

#

Confirm that the water pressure is not too high. If necessary, reduce the water pressure to the
recommended level.

3. Is air flowing through the channel connectors?

#

Check the tubing and ensure the tubing is free of kinks or bends.

#

Make sure the channel connectors are fully inserted.

#

Ensure the check valve that is in line with the alcohol manifold is not leaking air. If this is the case,
replace the check valve.

#

Make sure the air pump is not defective. If necessary, replace the air pump.

#

Check the internal air pump tubing to be sure it is not loose. If necessary, reconnect the tubing properly.

#

If air is flowing instead of fluid, the motherboard might be defective. If necessary, replace the
motherboard.

4. Is there fluid flowing through the channel connectors?

#

Check the channel connector tubing and make sure it is free of kinks or bends.

#

Make sure the channel connectors are fully inserted.

#

If the main pump is not activated by the motherboard, replace the motherboard.

#

Make sure the main pump rotates. If it does not, replace the main pump.

#

If air is flowing instead of fluid, the motherboard might be defective. If necessary, replace the
motherboard.

Troubleshooting: MV-1/MV-2 Control Panel

1. Are the lights off on the MV-1/MV-2 control panel?

#

Check the power cord to be sure it is connected.

#

Make sure the MV-1/MV-2 power switch is turned on.

#

Check the fuses. If necessary, replace the fuses.

#

Check the motherboard. If necessary, replace the motherboard.

«
...
15
16
17
18
»

Содержание MV-1



















Отзывы:

Нет отзывов