Olympic Medical BILI-LITE 33 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 56

Olympic Medical BILI-LITE 33 Скачать руководство пользователя страница 29

OLYMPIC BILI-LITE

Model 33/34 Instruction Manual

5-1

S e c t i o n

5

Maintenance

Cleaning the Bili-Lite

Required Items:

Cleaning cloths

Mild cleaning detergent (e.g., Virex

™

Tb, Virustat

®

, Coverage

®

)

Mild soap-and-water solution

Phillips-head screwdriver

To clean the Bili-Lite:

1

Press the power switch to the

OFF

(O) position, then unplug the power cord.

2

Allow the light to cool to touch before cleaning.

3

Dampen the cleaning cloth with either the mild soap-and-water solution or the

liquid disinfectant, then wipe down all exterior surfaces of the Bili-Lite. Use the

second cloth to dry all exterior surfaces of the Bili-Lite.

To clean the safety shield:

1

Remove the safety shield: First, remove the two retaining screws and washers.

Next, slide the safety shield out.

2

Dampen the cleaning cloth with the mild soap-and-water solution, then wipe the

surfaces of the safety shield. Use the second cloth to dry all exterior surfaces of

the Bili-Lite.

3

Slide the safety shield back into the light hood, then secure it in place with the

retaining screws and washers.

WARNING

Electrical shock hazard when the enclosure is open. Unplug the power cord from
the electrical outlet before cleaning this device.

Do not clean this device with flammables (e.g., antiseptics, cleaning agents).

CAUTION

Only qualified technicians should perform maintenance procedures.

Do not allow liquid to enter the light hood as liquids may cause a shock hazard or
damage the internal wiring.

Never use alcohol to clean the safety shield as alcohol will damage the plastic.

Keep the safety shield in place during phototherapy to protect the patient from
ultraviolet radiation and broken bulbs.

«
...
27
28
29
30
31
...
»

Содержание BILI-LITE 33

























































Отзывы:

Нет отзывов