background image

  OL5800 User Manual

 

 

5  

SAFETY INSTRUCTIONS FOR BATTERIES 

 
Safety Instructions for Batteries 
Handset Battery Pack  
 
CAUTION: 

Danger of explosion if battery is incorrectly replaced. Use only an Olympia Phone approved battery pack in the handset of 
your OL5800 Cordless Telephone. To reduce the risk of fire or injury, always do the following when replacing, discarding, or 
charging battery, When handling the batterie s, be careful not to short the battery with conducting materials such as rings, 
bracelets, and keys. The Battery or conducting material may overheat and cause burns. Use only the following type and size 
of battery pack: 

 

FOR HANDSET UNIT: 
GP60AAAH3BMX 3.6V 600mAh GPI INTERNATIONAL LIMITED 

 
 

CONTAINS NICKEL-METAL HYDRIDE BATTERY. BATTERY MUST BE 
RECYCLED OR DISPOSED OF PROPERLY 
 

 

Do not dispose of the battery in a fire. The cell may explode. Check with local codes for possible special disposal 
instructions. 
Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may 
be toxic if swallowed. 
Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets 
and keys. The battery or conductor may overheat and cause burns. 
Charge the batteries provided with or identified for use with this product only in accordance with the instructions and 
limitations specified in this manual. 
Observe proper polarity orientation between the battery(ies) and battery charger. 
Do not mix old and new batteries in this product. 
Do not mix batteries of different sizes or from different manufacturers in this product. 
 

SAVE THESE INSTRUCTIONS 

 

Содержание OL5800



























Отзывы: