Page
1 from
6
MAINTAINED/NON MAINTAINED ILLUMINATION SIGNS WITH GREEN LEDs
GENERAL
These new sign illumination luminaires, use a new
technology, friendly to the environment , with high
illuminated L.E.D.s. L.E.D. technology has very low
power consumption. The edge illumination sign is used
as a maintained backup lighting with indications
symbols. Each package contains arrows stickers which
are used to quickly design the required sign which is
suitable for each occasion.
Just place the sign on the figure which is designed on
the packages and stick the arrow.
Each model combines modern, aesthetics, together
with functionality. The exit illumination signs are used in
every public area where clear direction and good
appearance are important.
NON MAINTAINED OPERATION
By default the illumination sign operates as maintained.
The device has a possibility to operate as non
maintained. To change the maintained to non
maintained operation follow the relative instructions on
page 6. All models must be permanently connected to
the mains power supply as shown on page 2. The
legend is screened on to a clear acrylic sheet which
has the marking on the marking panel with the light that
comes from the top of the luminaire and diffracts, giving
light to the marking panel. The luminaire has an
indication (CHARGE) for the charging of the battery
and a (TEST) button to TEST the emergency circuit
and the LEDs for good operation only when the
luminaire is powered by the mains power supply. The
unit must be mounted in a clearly visible area and can
either be hung on a ceiling or mounted on a wall
depending on the requirements of the installation.
The package includes all the required materials for
mounting on the wall or on the ceiling. The pages
2,3 and 4 show us the mounting methods.
WARNING !!
1. Read carefully this instruction manual.
2. Before service interrupt the mains power supply.
3.
The device must be connected to the mains
power supply through a fuse dependent by the total
amount of the line’s power load
.
4. It is suggested to check every month the
indication LED for battery charging, and by pushing
briefly the TEST button to check the emergency
circuit. The sign should light for a few seconds
powered by the battery and then, will turn to normal
operation
. In the opposite condition contact the
installer.
5.
full
Every six months, a
duration check should be
carried out
by disconnecting the mains power
supply Count the autonomous duration of the
.
luminaire and in case of no correspondence to
stated emergency duration replace the battery The
.
replacement of the battery must be done using parts
of the same type, by the manufacturer or by a
competent person.
6.
In case of inactive use for a period greater than 2
months, disconnect the battery by pulling out the
battery’s connector.
7
Replaced batteries must not be thrown into
.
trash bins. They must be returned to
special battery disposal points. Do not
incinerate.
9225044
00
_09_027
Thank you for your trust in our product
Olympia Electronics - European manufacturer
MLD-34S/g
MLD-44S/g
MLD-28S/g
220-240V AC/50-60Hz
3h
24h
Overcharging and deep discharging protection
IP 40
class
II
3.6V/1Ah
22lm / 18lm
18lm / 18lm
ο
5
to
40 C
Up to
95%
280x100mm
305x25x155mm
3 years (1 year for the battery)
500gr.
800gr.
1160gr.
340x170mm
350x25x205mm
440x220mm
465x25x275mm
3W / 8VA
3W /
7
.
5
VA
TECHNICAL CHARACTERISTICS
(
for LED MODULE Specs. see page
4
)
Operation temperature range
Relative humidity
External panel's dimensions
External dimensions (LxWxH)
Typical weight
Guarantee
Mains voltage
Maximum power consumption
Battery (Ni-Cd)
Recharging time
Battery protection
Minimum emergency duration
Degrees of cover protection
Class of cover protection
Produced in accordance with
Light source intensity (Mains / Emerg)
Construction materials
ABS/PC,Plexiglass,PVC
EN 60598-1, EN 60598-2-1, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
