Page
1
from
5
923939015_09_004
GENERAL
These luminaires are used in places where
emergency luminaires are needed. Each
luminaire must be permanently connected to
mains power supply
.
In normal operation (L1
connected to L) the led strip lights and the battery
is charging. In case of a mains power supply
failure the luminaire will light the led strip
automatically in emergency mode (powered by
its battery). When the mains power supply is
restored the device turns to normal operation.
Address Operation
The luminaires can be connected to a GR-6500
address panel. For address operations refer to
the installation manual of the panel.
For address module connections see page 3.
For dip-switch addressing selection see page 3, 4
and 5.
INSTALLATION
To install the luminaire follow the installation
instructions on page 3.
Battery Charging
The battery charging is completely controlled
.
Thereby, the best possible battery maintenance is
achieved
,
as well as the elongation of its
duration
.
When the battery has completely
charged
,
it charges with a maintenance current.
Battery Cut-off
The luminaire enters in this operation when the
mains power supply fails
and battery has lost its
energy
.
During this operation the luminaire enters
the idle state
and battery consumption is
negligible, in order to be protected from deep
discharge.
Manual
Test
The manual test can be conducted only if the
mains power supply and the battery is connected.
By pressing the TEST/RESET button briefly
(page 3) an operation test is initiated. During this
test period all indication LEDs are OFF.
Tests
Normally the illumination source and the
autonomy tests are programmed by the control
panel and the test results are sent to the control
panel.
If the luminaire is not connected to GR-6500
panel, the following automatic tests executed:
Automatic Operational Test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the
mains power supply and the battery should be
connected.
ADDRESSABLE SELF TESTING MAINTAINED EMERGENCY LUMINAIRES WITH WHITE LEDs
220-240V AC/50-60Hz
4.5W / 4.9VA
Bayblend FR3010
,
transparent
polycarbonate
TECHNICAL CHARACTERISTICS
(for LED MODULE Specs. see page 5)
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (MAINS / EMERGENCY)
ILLUMINATION SOURCE
90min
24h
Charge, Lamp Fault, Battery Fault indication LED
From overcharge and deep discharge
IP65
3.6V/3Ah
210lm / 210lm
30 white LEDs
EN 60598-1, EN 60598-2-22
, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
o
5 to 40 C
Up to 95%
3 years
(1
year for the battery
)
950gr.
363 x 145 x 73 mm
3.4W / 3.8VA
GR-938/15L/ADR GR-938/30L/ADR GR-939/15L/ADR GR-939/30L/ADR
3.6V/
0.6
Ah
105lm / 105lm
15 white LEDs
180min
5.3W /5.6VA
3.3W / 3.7VA
3.6V/1.5Ah
210lm / 210lm
105lm / 105lm
30 white LEDs
15 white LEDs
810gr.
880gr.
Thank you for your trust in our products.
Olympia Electronics - European manufacturer
.
