Olivetti PR2 PLUS Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 172

Olivetti PR2 PLUS Скачать руководство пользователя страница 58

4-4

Service Manual

XZAC4219-05

14.

To save the new values you have configured for the
parameters, press the

STATION2

key to pass from the value

«NO» to the value «Y».

15.

The value «Y» is printed to confirm that the new configuration
values are saved.

16.

Press the

STATION1

key to save the new configuration.

NOTE:

if you do not want to save the new configuration, press the

STATION1

key when the value «SAVE

PARAMETERS: NO» is printed.

Procedure to save the value of a single parameter

The procedure illustrated above allows you to scroll through all the parameters of the menu selected, changing the
values of the parameters as required.

The procedure described below on the other hand allows you to change the value of a single parameter, exiting
immediately from the menu at the end without having to scroll through all the other parameters.

NOTE:

in this case also, let's imagine that we only want to change the value of the «INTERFACE»

parameter in the Configuration menu «CONFIG.».

1

Proceeding as indicated in the previous section, print the
setting of the fifth parameter «INTERFACE» that is to be
changed.

2.

This is the parameter that, in our example, we want to
change. Press the

STATION2

key to pass to the next value

for the parameter.

3.

The new value for the parameter is printed. For the
connection interface, 6 values are possible: «USB»,
«COM1-USB», «USB-PAR», «PARALLEL»,
«DUAL-PAR» and «SERIAL1».

4.

When you reach the value for the parameter desired, press
the

LOCAL

key to confirm the new value and exit from the

menu.

PRINT MODE:

STANDARD

BIM MODE:

MONO

PNS SELECTIONS:

N

SAVE PARAMETERS:

NO Y

SPECIAL FORMS:

N

MENU:

CONFIG.

DRAFT SPEED:

NORMAL

LQ TYPE:

LQ2

PAPER WIDTH:

FIRST LINE

BUZZER:

Y

INTERFACE:

USB

DRAFT SPEED:

NORMAL

LQ TYPE:

LQ2

PAPER WIDTH:

FIRST LINE

BUZZER:

Y

INTERFACE:

USB COM1-USB PARALLEL DUAL-PAR

SERIAL1

LQ TYPE:

LQ2

PAPER WIDTH:

FIRST LINE

BUZZER:

Y

INTERFACE:

USB COM1-USB PARALLEL

SAVE PARAMETERS:

Y

«
...
56
57
58
59
60
...
»

Содержание PR2 PLUS













































































































































































Отзывы:

Нет отзывов