Olivetti PR2 PLUS Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 172

Olivetti PR2 PLUS Скачать руководство пользователя страница 57

XZAC4219-05

Service Manual

4-3

6.

Also in this case, let's imagine that we do not want to change
this parameter. Therefore we press the

STATION1

key again

to pass to the next parameter.

NOTE:

the

STATION1

key is therefore the key that

confirms the value of the parameter

printed and

allows you to pass to the next parameter

.

7.

The setting for the third configuration parameter is printed.

8

Proceed in the same way pressing the

STATION1

key until the

setting of the fifth parameter «INTERFACE» is printed that we
want to change.

9.

This is the parameter value that, for the purposes of our
example, we want to change. Press the

STATION2

key to

pass to the next value available for the parameter.

10.

The new value for the parameter is printed. For the
connection interface, 6 values are possible: «USB»,
«COM1-USB», «USB-PAR», «PARALLEL», «DUAL-PAR»
and «SERIAL1». The values are displayed in a cyclical
fashion, therefore by continuing to press the STATION2 key,
you can return to the first value again.

NOTE:

the

STATION2

key is therefore the key that

allows you to change the value associated with

each parameter

. By pressing this key you pass to the next value available, in succession.

11.

When you reach the value you want to set for the parameter,
press the

STATION1

key to confirm the value and pass to the

next parameter.

12.

The next parameter is printed.

13.

Proceed in the same way, pressing the

STATION1

key for all

the parameters in the menu until the option «SAVE
PARAMETERS» is printed.

STATION1=confirm STATION2=Skip Press Local to continue

MENU:

CONFIG.

DRAFT SPEED:

NORMAL

LQ TYPE:

LQ2

PAPER WIDTH:

FIRST LINE

MENU:

CONFIG.

DRAFT SPEED:

NORMAL

LQ TYPE:

LQ2

PAPER WIDTH:

FIRST LINE

BUZZER:

Y

INTERFACE:

USB

DRAFT SPEED:

NORMAL

LQ TYPE:

LQ2

PAPER WIDTH:

FIRST LINE

BUZZER:

Y

INTERFACE:

USB COM1-USB PARALLEL DUAL-PAR

SERIAL1

LQ TYPE:

LQ2

PAPER WIDTH:

FIRST LINE

BUZZER:

Y

INTERFACE:

USB COM1-USB PARALLEL DUAL-PAR

SERIAL1

RSI EMULATION:

OLIVETTI

PRINT MODE:

STANDARD

BIM MODE:

MONO

PNS SELECTIONS:

N

SAVE PARAMETERS:

Y

SPECIAL FORMS:

N

«
...
55
56
57
58
59
...
»

Содержание PR2 PLUS













































































































































































Отзывы:

Нет отзывов