Olivetti PR2 PLUS Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 172

Olivetti PR2 PLUS Скачать руководство пользователя страница 56

4-2

Service Manual

XZAC4219-05

8.

To pass to the next menu, press the

STATION2

key.

The new menu is printed and you can change the parameters
related to the «IBM» emulation.

9.

Pressing the

STATION2

key again, you can pass to the third

menu.

10.

The new menu is printed and you can change the parameters
related to the «OLIVETTI» emulation.

11.

These menus operate in a cyclical fashion therefore, when the

STATION2

key is pressed again, you return to

the initial menu «CONFIG.».

12.

Therefore, select the menu for which you want to change parameters, and proceed to configure them as
described in the next section.

Modifying configuration parameters

NOTE:

the procedure below illustrates the steps to follow to change the configuration parameters.

In this example, the procedure is described for modifying the fifth parameter «INTERFACE» in the
Configuration menu, «CONFIG.». To change the configuration of the other parameters proceed in a
similar way.

NOTE:

1.

Enter the Configuration menu following the procedure
described in the previous section. The currently active menu
is printed.

2.

Press the

STATION1

key.

3.

The setting for the first configuration parameter is printed.

4.

Let's imagine that we do not want to change this parameter.
Therefore we press the

STATION1

key again to pass to the

next parameter.

5.

The setting for the second configuration parameter is printed.

STATION1=confirm STATION2=Skip Press Local to continue

MENU:

CONFIG. IBM

STATION1=confirm STATION2=Skip Press Local to continue

MENU:

CONFIG. IBM OLIVETTI

STATION1=confirm STATION2=Skip Press Local to continue

MENU:

CONFIG.

STATION1=confirm STATION2=Skip Press Local to continue

MENU:

CONFIG.

DRAFT SPEED:

NORMAL

STATION1=confirm STATION2=Skip Press Local to continue

MENU:

CONFIG.

DRAFT SPEED:

NORMAL

LQ TYPE:

LQ2

«
...
54
55
56
57
58
...
»

Содержание PR2 PLUS













































































































































































Отзывы:

Нет отзывов