manualshive.com logo in svg

Olivetti PR2 PLUS, Руководство по обслуживанию, Страница: 166 / 172

Поделиться
Скачать
Olivetti PR2 PLUS Скачать руководство пользователя страница 166

A-4

Service Manual

XZA4219-05

FIRMWARE AND CHARACTER GENERATORS

Machine firmware

In addition to that separate from the generator and from the set characters, the management firmware of the printer 
is controlled independently in load operations in order to facilitate immediate access for modifications to the 
characters area.

The basic memory of the printer is a 1-MB Flash EPROM on which the management FW, character generators and 
characters sets are held and can be replaced on line.

A second Flash EPROM (optional) with the same capacity, able to contain complex character sets or high volumes 
of macros and logos, can be installed on the motherboard.

The machine firmware comprises the following emulations:

•

Olivetti environment: STD 12/14 controlled protocol with native PR2 E environment and PR40+ and PR2845 
emulation. Industry standard emulation IBM Proprinter II and Proprinter X24.

•

IBM environment: Emulation protocol 9068 with coverage of the 4722 model, Industry standard emulation IBM 
Proprinter II and Proprinter X24.

•

Wincor-Nixdorf environment: Emulation protocol SNI 4915 with coverage of models 4905, Industry standard 
emulation EPSON LQ 2550.

Character sets

System level compatibility for each character set extends the environments listed below:

Each emulation present on the machine includes one or ore character sets. The character sets present in each 
emulation are listed in the table below:

Mode and character fonts

The characteristics of the various print modes are listed below:

ENVIRONMENT

CHARACTER SET 

PC/DOS

CP SET, CODE PAGE

WINDOWS 2.X, 3.0; OS/2; UNIX

ISO 8859/X

WINDOWS 3.1

CP SET

OLIVETTI

STD 15

EMULATION

CHARACTER SET

OLIVETTI

CP SET, STD 15 Olivetti, ISO

IBM

CP SET, ISO

10 cpi

12 cpi

15 cpi

H.S.D. (High Speed Draft)

350 cps

314 cps

327 cps

DRAFT

260 cps

260 cps

260 cps

N.L.Q. (Near Letter Quality)

130 cps

130 cps

130 cps

L.Q. (Letter Quality)

86 cps

104 cps

131 cps

Содержание PR2 PLUS













































































































































































Отзывы:

Нет отзывов