Olivetti PR2 PLUS Скачать руководство пользователя страница 163

Страница: 163 / 172

XZA4219-05

Service Manual

A-1

APPENDIX A

ACCESSORIES

This section describes the accessories available for the PR2 plus printer.

Ribbon cartridge in black NYLON SNUG CART

The ribbon cartridge provided for the product is of disposable type.

It is designed in way that allows the operator - following the indications given both in the manual and on the
container of the new ribbon - to carry out the operations required for its replacement without coming into contact
with the inked ribbon.

Figure A - 1

Ribbon cartridge

Ribbon cartridge in NYLON SNUG CART - indelible

Same as the BLACK NYLON SNUG CART but with indelible ink.

Colour

Black

Pigmentation

Carbon-free

Vita ribbon

10 million characters (draft mode, 40% contrast)

no. ribbons/year

1,9

no. ribbons/
life-time

9,4

Packaging

Waterproof with protective box

Содержание PR2 PLUS












































































































































































Результаты поиска

Содержание PR2 PLUS

Отзывы:

Olivetti PR2 PLUS, Руководство по обслуживанию, Страница: 163 / 172

Результаты поиска

Содержание PR2 PLUS

Отзывы: