Olivetti PR2 PLUS Скачать руководство пользователя страница 161

Страница: 161 / 172

XZAC4219-05

Service Manual

8-3

When the printer configuration is complete, activate the printing test (see the section

“Activating and

deactivating the print test” on page 2 - 10

) in the CONFIG. section the following string should appear:

How to print Ethernet LAN card properties

Power on the printer with

STATION1

and

LOCAL

keys

pressed together.

At the end of the phase for resetting the mechanics, check
that the

and

Ready

LEDs are illuminated.

Insert a sheet in A4 format into the front slot.

A line of text is printed which indicates the functions of the

STATION1

, STATION2 and LOCAL keys for the printer in the

current configuration.

Press

STATION1

key and the printer will print the Ethernet LAN Card settings (insert a new A4 document if

needed).

Figure 8 - 4

Ethernet LAN Card settings

STATION1=confirm STATION2=Skip Press Local to continue

Содержание PR2 PLUS












































































































































































Результаты поиска

Содержание PR2 PLUS

Отзывы:

Olivetti PR2 PLUS, Руководство по обслуживанию, Страница: 161 / 172

Результаты поиска

Содержание PR2 PLUS

Отзывы: