Olivetti PR2 PLUS Скачать руководство пользователя страница 133

Страница: 133 / 172

XZAC4219-05

Service Manual

7-13

Printhead drive motor disassembly/reassembly

Remove the upper mechanical assy as explained above. See the section

“Printhead disassembly/reassembly”

on page 7 - 10

Loosen the lock-screw

(1)

of the idler pulley support slide and release the carriage movement belt from the

motor pinion.

Unhook the flat cable of the printhead loosening the screw

(2)

Back off the three special lock-screws

(3)

and extract the printhead movement motor from its housing, taking

care not to damage the ribbon feed gears.

Figure 7 - 15

Removing the motor for printhead movement

NOTE:

during reassembly, correctly reposition the ground clip (4) and adjust the carriage drive belt. See

the section

“Replacement and adjustment of belt for carriage movement” on page 6 - 15

Содержание PR2 PLUS












































































































































































Результаты поиска

Содержание PR2 PLUS

Отзывы:

Olivetti PR2 PLUS, Руководство по обслуживанию, Страница: 133 / 172

Результаты поиска

Содержание PR2 PLUS

Отзывы: