Olivetti PR2 PLUS Скачать руководство пользователя страница 126

Страница: 126 / 172

7-6

Service Manual

XZAC4219-05

Mechanical assy disassembly/reassembly

Disassembling the casing. See the section

“Casing disassembly/reassembly” on page 7 - 4

On both sides, back off the lock-screws

(1)

of the tabs that fasten the front rubber pads so that these can be

removed from their housing.

Figure 7 - 6

Disassembling the mechanical assy

From the front, lift the entire mechanism from the base plate and rotate it partially so as to access the
connectors of the motherboard.

Disconnect all the connection cables of the mechanism to the motherboard, except for the motherboard - power
supply unit connection cable.

Figure 7 - 7

Disconnecting the cables

Loosen the lock-screws

(2)

of the tabs that fasten the rear rubber pads so that these can be removed from their

housing.

Back off the screw

(3)

that fastens the ground cables.

Lift the mechanical assy and separate it from the base plate.

Printers with serial number 8.xxx.xxx

Printers with serial number 1.xxx.xxx

Содержание PR2 PLUS












































































































































































Результаты поиска

Содержание PR2 PLUS

Отзывы:

Olivetti PR2 PLUS, Руководство по обслуживанию, Страница: 126 / 172

Результаты поиска

Содержание PR2 PLUS

Отзывы: