Olivetti PR2 PLUS Скачать руководство пользователя страница 11

Страница: 11 / 172

XZAC4219-05

Service Manual

1-1

Chapter 1 - OVERVIEW

INTRODUCTION

The

PR2 plus

is a mid-range specialized printer for the banking environment able to handle documents (both multi-

copy and not) and passbooks for deposit/withdrawal transactions.

This highly versatile printer can also be used for Public Administration front-office transactions or in Post Offices.

The

PR2 plus SC

model of the printer integrates a colour scanner with a front/back 600 dpi resolution The printer

can be configured with the following optional components:

•

"Horizontal Magnetic" unit for reading/writing horizontal magnetic stripes

•

MICR (Magnetic Ink Character Reader) unit for reading CMC7 / E13B characters printed on cheques.

•

Console with optional LCD display (shown in the following figure).

The

PR2 Plus

printer is available with or without an LCD display.

The table below indicates the different configurations in which the PR2 Plus printer is available:

Figure 1 - 1

PR2 Plus Printer

VERSION

CONFIGURATION

PR2 plus 10

Basic model with RS232, Parallel and USB ports

Basic Model - Passport version

PR2 plus SC

Model PR2 plus 10 with scanner

PR2 plus 12

PR2 plus 10 with horizontal magnetic unit

PR2 plus 12 M

PR2 plus 12 with horizontal magnetic unit and MICR reader

Содержание PR2 PLUS












































































































































































Результаты поиска

Содержание PR2 PLUS

Отзывы:

Olivetti PR2 PLUS, Руководство по обслуживанию, Страница: 11 / 172

Результаты поиска

Содержание PR2 PLUS

Отзывы: