Olivetti PR2 PLUS Скачать руководство пользователя страница 103

Страница: 103 / 172

XZAC4219-05

Service Manual

5-19

Faults with document handling

Fault

Possible cause

Solution

The machine does not

intr

oduce/eject the

document

The document

fed crookedly

The document

wrink

led

The document

has irregular line feeds

Document not acc.
to specs

Check the dimensions and the type of the document . See

“DOCUMENTS THAT CAN BE HANDLED BY THE BASIC
MACHINE” on page 1 - 3

Document ruined

Use another document.

Closing levers open

Lower the lever for closure.

Front
photosensors
fault

Carry out the calibration procedure. See the section

“CALIBRATING THE PHOTOSENSORS” on page 4 -
18

Clean and if necessary replace the fault photosensor.

See

“PROCEDURE FOR CLEANING / REPLACING

THE PHOTOSENSORS” on page 6 - 2

Paper
photosensor
fault

Adjust the sensor position. See the section

“Adjusting

Paper Photosensor” on page 6 - 8

Carry out the calibration procedure. See

“CALIBRATING THE PHOTOSENSORS” on page 4 -
18

Clean and if necessary replace the fault photosensor.

See

“PROCEDURE FOR CLEANING / REPLACING

THE PHOTOSENSORS” on page 6 - 2

Service motor fault

Replace the services motor. See the section

“Services

motor disassembly/reassembly” on page 7 - 14

Paper feed
motor fault

Replace the paper feed motor. See

“Paper feed motor

disassembly/reassembly” on page 7 - 12

Adjustment of needle
roller incorrect

See

“Adjusting the roller gears” on page 6 - 9

Print bar not adjusted
correctly

See

“Adjusting the print bar (where torsion bar present)”

on page 6 - 4

“Adjusting the print bar (where torsion bar

absent)” on page 6 - 5

Band not adjusted

Adjust the printing band. See

“Adjusting the print bar

parallelism and leaf spring load on the basic machine” on
page 6 - 6

“Adjusting parallelism of print bar (without

torsion bar)” on page 6 - 7

Roller gears not
adjusted

Adjust the gears. See

“Adjusting the roller gears” on

page 6 - 9

Содержание PR2 PLUS












































































































































































Результаты поиска

Содержание PR2 PLUS

Отзывы:

Olivetti PR2 PLUS, Руководство по обслуживанию, Страница: 103 / 172

Результаты поиска

Содержание PR2 PLUS

Отзывы: